Trailer Axle Beam with Easy Grease Spindles - 89" Long - 5,200 lbs
(172 reviews)
Price: $213.03
In Stock
Trailer Axle Beam with Easy Grease Spindles - 89" Long - 5,200 lbs
Item # e55GR
Our Price: $213.03
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (172)
- Q & A (0)
- Photos
etrailer Trailer Axles - e55GR
- 5200 lbs
- 89 Inch Long
- 74 Inch Long
- Spindles Only
- No Drop or Lift
- Leaf Spring Suspension
- No Hubs
- etrailer
- Easy Lube Spindles
Round trailer axle beam measures 89" from hub-face-to-hub-face (when hubs - sold separately - are mounted) and 74" from spring-center-to-spring-center. Easy Grease spindles make it easy to lubricate bearings (sold separately).
Features:
- Round axle beam acts as part of your trailer's suspension system
- Replace an axle on your trailer
- Fabricate a suspension to fit your application
- High-strength steel construction
- Bend in axle creates zero camber angle for even road-to-tread contact across the width of your trailer's tires
- Best for straight-line acceleration and steady, controlled towing
- Underslung design - spring seats welded to underside of axle for mounting leaf springs (sold separately)
- Low ride height makes it easier to load and unload your trailer
- Straight, Easy Grease spindles - no drop
- Patented welding process prevents spindle failure with 40% stronger welds
- Built-in grease zerk for simple lubrication
- Spring seats and spindles are welded on
- CSA, QAI, and SAE-N certified
- Lifetime technical support from the experts at etrailer.com
- Made in the USA
Specs:
- Weight capacity: 5,200 lbs
- Hub-face-to-hub-face length: 89"
- Spring-center-to-spring-center length: 74"
- Axle diameter: 3"
- Spindle/hub compatibility:
- Bearings: 25580 inner, 15123 outer
- Seal: GS2250-DL, inner diameter 2.25"
- Limited lifetime warranty
Axle Dimensions
There are multiple ways to measure the length of an axle beam, but the hub-face-to-hub-face and spring-center-to-spring-center lengths are the most accurate. Hub face (A) refers to the length of the axle measured from the base of one wheel stud to the base of the wheel stud on the opposite side of the axle (when hubs are mounted on the beam).
The spring center (B) is the approximate width of your trailer. It is measured from the center of the spring seat on one side of the axle to the center of the seat on the other. This axle beam comes with the spring seats welded on.
If you are replacing your trailer's axle, you should be able to figure out which type you need by determining your trailer's capacity, the bolt pattern of your wheels, the brake type and the aforementioned lengths.
etrailer Axles
etrailer axles are made of high-strength steel and come with spindles and spring seats welded on. The spring seats are attached to the underside of the axle so that the leaf springs (sold separately) can mount beneath the axle. The result of this underslung design is a trailer that rides a bit lower for quick and easy loading and unloading.
Each axle is manufactured to create a certain camber angle. This ensures that the angle of the wheels is correct for your towing needs. Because the primary concern when towing is maintaining controlled, in-line movement, each axle is made so that your trailer's tires will run along the pavement evenly, with contact across the width of the tread. The result is excellent straight-line acceleration for steady, in-line tracking. You might notice the bend near the center of the axle; this is what ensures the proper camber angle. Having the center ride a bit higher and the sides of the axle bent lower allows the axle to give just enough to compensate for the load.
e55GR etrailer by AxleTek Replacement Axle Beam - Easy Grease - 89" Hub Face - 74" Spring Center - 5,200 lbs
Customer Satisfaction Score:
90% were satisfied with this product
10% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Trailer Axle Beam with Easy Grease Spindles - 89" Long - 5,200 lbs - e55GR
Average Customer Rating: 4.7 out of 5 stars (172 Customer Reviews)
Round trailer axle beam measures 89" from hub-face-to-hub-face (when hubs - sold separately - are mounted) and 74" from spring-center-to-spring-center. Easy Grease spindles make it easy to lubricate bearings (sold separately).by: Josh03/08/2024
I haven’t installed the axle yet, but it looks to be pretty solid. Time will tell. Irrelevant to the axle, but I have to touch up some paint where UPS dropped it down on my concrete. Not a big deal though. It’s going to get beat up by road debris anyway.
by: Drew05/12/2023
Don't change anything you guys do . Very impressive . My axle shipped shortly after I ordered it, and on Sunday. Love the tracking setup and fast shipping. Not to mention the price and nice quality. Thanks
by: Victor 07/14/2023
Everything was great condition and worked perfectly.
by: Gary05/01/2023
by: Bobby 12/06/2023
by: Lance 03/22/2024
by: Jamyn08/01/2023
by: Charles 04/05/2024
by: Anthony 01/05/2024
by: Marvin 08/18/2023
by: Rodney03/15/2023
by: Shawn 10/23/2022
by: Rodney 10/19/2022
by: Jason05/30/2023
The axles that I ordered last year are still working out great. But even better than the parts was the service I got from etrailer. It was so great working with a company who took the time to listen to my project and help me get the right parts I needed, especially coming right off the heels of a terrible experience dealing with bad information and wrong parts from a competitor. Even with some damages in shipping, the returns/ and replacements were no hassle, with most issues being quickly resolved and not even costing me any additional downtime. As a contractor keeping a small fleet rolling, your competency and professionalism have made me a customer for life!! You guys at etrailer will be my first stop for trailer parts.
by: 11/30/2023
Welds looked good however the assembler failed to rotationally align the weld on spindle/brake mounts properly. One was about 3 degrees off and the other side was an 9.5 degrees from the 12 oclock position. Not sure about the thickness of the tube. Kind of strange to look at when the top of the brake system is not at 12 oclock. Found this after I removed the spring pads on this 2.1 degree camber axle so I had to jig the tube to fine zero toe to locate the new pads as the 2.1 camber tube changes wheel alignment depending on the bend/ springpad relationship. Not sure the AVG JOE is going to be able to move the spring pads when the brake mounts can't be used as a reliable ref point. If the toe is off from improper pad rotational location. the trailer will eat tires at best or worse cause a loss of controlled tracking and someone could get get killed.
by: John04/26/2024
Replaced the old axles with these on my 7x16’ equipment trailer, been nothing but amazing since I’ve installed them. Hauled thousands of pounds since and with minor greasing and normal maintenance they’ve been great.
by: Mark04/16/2023
So far performing well. Have not been able to use trailer yet as much as I wanted to, don't use the grease nipples. Its easy to regrease without.
by: Gina10/19/2023
Everything is working perfect with that replacement axle. I have definitely put it to the test a lot of miles with a lot of weight. Very highly recommended.
by: Tom 11/17/2022
Very easy installation. Everything fit perfect.
by: Patrick 04/16/2024
Always hair free when I buy from ev tra iler
by: Bob W02/08/2024
The mounts were 1/2 inch closer than advertised. I was able to persuade the springs inward to compensate. Good price and fast shipping.
by: Terry07/11/2023
Axle arrived fast, was exactly what I ordered and needed. Install went well with no problems.
by: Ralph03/07/2024
Received. Cannot use till all parts come
by: David 09/28/2023
The axle was exactly what I ordered and showed up much quicker than I expected. I installed it in about an hour. Good quality. Having the wire for the brakes already ran inside the axle made it very easy to rewrite the brakes, nice feature.
by: Douglas 07/10/2023
Worked great on my trailer.
It is a older trailer and I needed to move the anchor points on the axel but that was not difficult to have done.
Axel works great.
I love the easy grease feature.
25
170
Show More Reviews
See what our Experts say about this etrailer Trailer Axles
- Replacement 3 Inch Diameter Axle Beam with 95 Inch Hub Face DimensionAn axle with a 3 inch diameter axle tube typically has a 5200, 6000 or 7000 lb capacity. The inner and outer wheel bearings would be the determining factor that would tell you the actual capacity. We do have 95 inch axles (hub face to hub face dimension) but none of our offerings have the proper spring seat spacing, so you'd need to add seats in the correct locations. • For a 95 inch 5200 lb axle with spindles compatible with a 25580 inner/LM67048 outer bearing, use # e55GR • For a 95...
view full answer... - Replacement Spindle/Axle Option For a 4,500LB Mobile Home AxleThe #42 E-Z Lube Spindle w/ Flange # TRU37FR is going to be the best option for replacing your spindle on your mobile home axle. Do remember that mobile home axles were never designed for continuous use and are not as structurally strong as a Axle # e55GR. This particular axle has the same #42 spindle and a 89" hub face to hub face measurement. We do offer the Dexter Trailer Hub and Drum Assembly # 8-174-5UC3 which has the 5 spoke utility mounting holes like the Dexter 8-222. You will need...
view full answer... - Overall Length of etrailer Trailer Axle Beam # e55GR & Dexter Trailer Axle Beam # 8327820Both the etrailer Trailer Axle Beam # e55GR and Dexter Trailer Axle Beam # 8327820 are 95-3/8" long from tip of grease zerk to tip of grease zerk. Both axles also share the same hub face of 89" and spring center of 74".
view full answer...
- Availability of 5,200 lb Axle With Idler HubsAlthough we do not have a version of the # e75SR that comes with idler hubs, we do have the parts needed to put this together. All you need is the # e55GR along with the Easy Grease Trailer Idler Hub # AKIHUB-655-6-EZ-K. This is pre-greased so it is ready to go. The hubs have a slightly higher capacity at 6k but they use the same bearings and grease seal so it won't hurt anything. You will still be limited by the 5,200 lb capacity of the axle.
view full answer... - How to Measure for Adding Lippert Bolt-On Shock Kit for 3 Inch Axles to TrailerIf you're upgrading to a 5,200 lb 3" axle and you're planning on placing it under the leaf springs then you need the Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks # LC281281. The full instructions have been linked to this answer page for you to reference but I've cut out the part of the instructions that has to do with determining where to place the mounting bracket for the shocks on the trailer frame. The "4A + 2" measurement is going to come out to 11-1/16" + 2" so that will be 13-1/16"...
view full answer...
- Wall Thickness of 3,500, 5,200 and 6,000 lb Trailer Axles3,500 lb trailer axles like the # T3584F-8974 and # e38GR have a wall thickness of .16 inch whereas 5,200 lb axles like part # 8327820 and # e55GR have a wall thickness of .18 inch. 6k axles like the part # 8327830 also have a wall thickness of .18 inch.
view full answer... - Replacement Trailer Axle Option for 1999 Triton Boat TrailerThe best match replacement we have for your trailer is the Trailer Axle Beam with Easy Grease Spindles part # e55GR which has an 89" hub face, 74" spring center, and 5,200 lb weight capacity. The hub face is longer than what you have but only by an 1" so the wheels and tires will stick out about 1/2" more per side. The spring centers don't match up either but you can move these inward by cutting the old ones off and tack welding them where you need them. If you need a higher capacity, this...
view full answer... - Lippert Center Point and Electric-Over-Hydraulic System for a 2017 Dutchman Voltage 3005The closest axle that we have to what you're needing is the Trailer Axle Beam with Easy Grease Spindles # e55GR rated for 5,200 lbs. This has an 89" hub-face measurement and a 74" spring-center measurement which is really close to what you have but slightly off so I recommend having a shop custom-order one for you to make sure it matches up directly. For the Lippert Center Point you need the kit # LC1565401 which is their setup for triple axle trailers (which is what I'm seeing for your...
view full answer... - Can 89 Inch Axles With 74 Inch Spring Centers Fit 74-1/2 Inch Spring CenterYou'll be perfectly fine going with a 74 inch spring center to spring center axle with 74-1/2 inch spring center. That said we don't have 64 inch hub face to hub face axles with 74 inch spring centers, only 89 inch hub face to hub face and 74 inch spring centers. There are a few different options depending on the axle capacity you need: - 3,500 lbs: Trailer Axle Beam with Easy Grease Spindles # e38GR - 5,200 lbs: Trailer Axle Beam with Easy Grease Spindles # e55GR - 6,000 lbs: Trailer...
view full answer... - Can I Upgrade 3,500 lb Axles to 5,200 lb Axles on a BudgetThank you for reaching out! The best thing for your situation is to go with the 3,500 lb Dexter Axle # T3584F-8974 you are looking at. While you can upgrade your axles to the 5,200 lb # e55GR, you won't really see a benefit from it unless you also upgrade your trailer suspension and then reinforce the frame so it can safely handle the extra weight of your cargo. When you toss in the fact that you're wanting to use the same equipment from your old axles that also helps clear things up...
view full answer...
- What Is The Difference Between 5,200lb Axle e55gr and 6,000lb Axle e23gr?Sure is! The only difference between the 5,200lb axle # e55GR and 6,000lb axle # e23gr is the wall thickness of the tubing. They both use the same spindle as it's actually the outer bearing and race in the hub that give extra strength and not the spindle diameter themselves. Since both of these axles are the same length, and same spring seat length, I'd just go with the 6k # e23gr for some extra peace of mind. This won't increase the capacity of your trailer if you originally had 5,200lb...
view full answer...
Do you have a question about this Trailer Axle?
Info for this part was:
Edited by:
Lindsey S
Video by:
Jacob T
Video Edited:
Chris R
Updated by:
Leah S
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Carrie F
Installed by:
Conner L
Installed by:
Michael B
Written by:
Mike S
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Brooke M.
5/1/2023
We want to know what you have to say about this axle. If you would like to add any comments, please let me know.