To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Mount this 7-way, RV-style connector in your truck bed for quick, simple hookup of your 5th-wheel or gooseneck trailer. Custom harness plugs in-line with your existing factory wiring so that you can retain use of your Ram 2500's factory 7-pole.
Features:
Specs:
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today I have a 2013 Dodge Ram 2500. We're going to be installing the Curt 5th wheel gooseneck custom wiring on this 7 hole connector, part number C56070. This is what it's going to look like when installed. This is going to come in handy, because you're not going to have to take your gooseneck or 5th wheel trailer wiring and run across your tailgate to plug it into the back of your truck, and possibly come unhooked. It's going to be inside the bed and secure. Now let's go ahead with our install. First thing we're going to want to do is take our 7-way connector out of the box, and figure out where we would like to place it. Now on our vehicle, we determined that this location right here is going to be perfect.
It's through the double wall, so it's far enough away from the outside of the truck that you're not going to damage anything. We've checked behind there, there's nothing there, so we're going to go ahead and inaudible 00:00:53 hole. Now we'll take our 2 1/8 hole saw, and we'll enlarge the hole. On the bottom side, behind the driver's rear wheel, you can see up in here is where we drilled our hole that came through. We're going to take our new jumper harness, and we're going to go from there to the factory 7-way connector, which will be located right here. We're simply going to unplug the factory one.
Squeeze the tab, pull it back, there's a little push tab right there, you just push in on that and you can just pull it back. Then you'll take your new harness, which is basically a jumper, you're going to take your new plug, you're going to snap it into the factory 7-way connector, push it in until you hear it click. You do the same thing with the other side of your new harness. Squeeze it nice and tight, then we're going to route our new wire up across, try to follow your factory harness the best that you can. Keep out of the way anything that's going to be moving or could potentially have some heat in it.
Then we'll take our new plug and push it up and plug it through the hole on that side. Now we can go to the topside and we can connect our other plug with the four screws that are supplied with it. Now, on our new plug, it's not a bad idea to put a little bit of dielectric grease on here, just to protect it. We'll take our supplied self-tapping screws, set it level, all around there. Now we can go to the bottom side, and we'll secure our wires. Then we're just going to take it, and we're going to zip tie it out of the way. We want to make sure it's not going to come in contact with anything, or flop around in there. Once you get over here and you have your access, you can just take it and loop it up, and we'll attach it up to the bottom of the body.
That will keep it nice and tucked out of the way. You just go along and cut off the end of the ties. We're going to be testing it with a Tekonsha 7-way trailer emulator laced out connector, part number 6562, available on our website. We've got our power, that's lit up. Let's go ahead and get some brakes, and left turn, right turn, and let's get a reverse light, and the trailer brake. Everything works. If you don't have one of these at your house, you can use a test light to test the circuit, it's all marked on the package. That's going to wrap up our install and look at the Curt 5th wheel-gooseneck custom wiring harness with 7 pull connector, part number C56070 on our 2013 Dodge Ram 2500.
Average Customer Rating: 4.8 out of 5 stars (901 Customer Reviews)
Mount this 7-way, RV-style connector in your truck bed for quick, simple hookup of your 5th-wheel or gooseneck trailer. Custom harness plugs in-line with your existing factory wiring so that you can retain use of your vehicle's factory 7-pole.Connecting to the existing wire harness was straightforward and easy on the other-hand finding a place on the side wall wasn’t easy. I put the plug together and measured and could not find a place with enough space between the inner and outer sheet metal. Maybe there was but I didn’t want to chance it, did not want a hole I couldn’t use. i ended up putting it in the post behind the tail light. I used the round area in the tail light area as a guide (see pic). To get the wire up through from beneath the light I cut a small piece of metal to allow the wire access (see pic). I am very happy with the location where the plug will not be damaged.
I used this cable to replicate 7-pole to the bed of a Ram 2500.
I also have a 4-pole at the bumper and wanted to have all three locations 'hot'.
This cable does not "move" the functionality.
It REPLICATES it, while keeping the 4-pole functional.
7-pole at bumper or 7-pole in bed.
4 pole at bumper.
I used the 120v factory hole because this truck does not have an inverter, nor will I be adding one. The 5th wheel camper has that.
I did have to fabricate an 'adapter' to cover the factory mounting holes, but that was easy and is now a rubberized, waterproof mounting.
All good.
Thanks Paul!
2018 Ram 2500 w/6.5' bed
Quality seems good. Install easy. Works fine if you plan on putting the plug in the back of the bed. Will not reach to the front wheel wells though! Putting in an extension as this is for a slide-in camper.
This harness seemed to be of great quality however after installing and attempting to use for the first time I discovered that it disrupted the signal to my 7 way at the bumper.
Just what I needed. The harness that came with the truck developed a short I couldn’t track down to repair. I got the lovely ding and check trailer brake wiring every time i hit the brakes. That got annoying really quick. Replaced it with this one and it solved my issue. Seems like it’s quality built and will withstand a few Colorado winters. It’s only downside is it comes with like 6 small zip ties to install it. If you’re the least bit OCD and want a clean look grab a dozen large ones from an auto part store.
I bought the wiring harness to transfer my trailer electricity from back bumper to inside bed of my Sierra 1500. Everything went smooth and I loved drilling a two inch hole in the bed of my truck. Done in less than one hour.
etrailer was familiar with this product and they were very friendly and easy to deal with.
The trailer wiring harness worked great. No problem with installation.
Plug and play!! The hardest part was to decide exactly where I wanted to mount it in the box.
2022 ram 3500 long bed. Was perfect length if you install it on the rear driver side of bed. In the video i saw of someone installing it they cut the hole then shoved the double connector end of the harness down from the bed. I found it easier to fish a string down the hole and then tie the string to the clip part of the single side of the harness and pull it up. That plug has to go through the hole straight or else it gets caught up and having the string tied to the clip helps pull it up and through the hole straight.
excellent service, have bought from E-trailer several times, always good quality products and service
Was a 30 minute install on my Ram 2500. It took longer to raise/lower the spare than anything else. Do yourself a favor and get the shorter one. You don’t need 7’, and I have at least 2’ coiled up.
This order was for ITEM # C53CR which has the filler plate. The order somehow was changed or substituted for this part which works for the application but without the filler plate.
etrailer sent the filler plate separately and I performed the install which was fairly simple and with the plate installed looks completely like factory. I attached my camper to the bumper connector and all worked, I could not reach the bed connector due to cable length, this was set up for a new 5th Wheel we are purchasing. I am confident that is will work.
I used different wire ties, something a little more substantial than what was provided but that is my choice. Watch the install video, it is fairly straight forward, 30 minutes from start to finish for my install.
4 stars due to the confusion in the order but was eventually straightened away.
The purchase was great and the product and installation were very good!
Install was very easy, wish it would come with some of that gel you’re suppose to put inside of it. Just needs a little and no need to buy a whole big tube of it. Haven’t used it yet but was everything I needed for my Fords new gooseneck. Didn’t want to plug it in at bottom of bottom of bumper
Nicolas
4/15/2021
Has worked great
Great kit to add a trailer connector in the bed of your truck. Super easy to install, took 30 minutes start to finish.
William
8/15/2023
Still works great to hook up my fifth wheel connector in the bed of the truck instead of having it hang over the tailgate.
Super fast install. Great product. I have a 21 Ram crew short bed and the 7’ is the way to go. 35 min install. Tested and works great. Instructions call for a 2-1/8 hole. I was able to use the 2” hole saw and remove and reinstall the grey plastic wire cover from the Y.
Super easy to install. Lighting fast de livery.
I ordered one from somewhere else that was a different brand and lets just say I was wrong. This one by Curt plugged right in and worked just like it should. since I already had the hole cut it took about 5 minutes to slap it together. Great product and great shipping.
Excellent product, which was super easy to install using the videos from the e trailer website
Installation was very easy and straightforward. It took about 10 minutes; once the spare tire was out. The hardest part was taking out and putting back in, the spare tire. If you have a 5th gen Ram that didn’t come with a gooseneck plug, there should be a plastic cover where it would be. Pop that out and your hole for the wiring is already there. There will be four small squares in the corner. The plug that is mounted to the firewall has enough clearance, so you can mount it to the bed using the provided self-tapping screws.
I purchased this unit after reading the reviews. I received both the C56070 and a B&W OEM hitch within a few days of placing my order. Etrailers’s customer service is excellent! The installation of this wiring harness took about twenty minutes including cutting the hole for mounting. Everything but the hole saw was included in the package! I am very pleased with my purchase!
Be sure to watch their installation videos prior to purchasing, they give real insight into the process!
The plug in is located in the bottom left corner of the photo!
Great product! a 10 for sure.
The 7 foot cord was more than adequate. Good quality product. I installed on 2019 Ram 2500 Big Horn.
I will tell you dont even try the install without lowering the spare tire. Even if you are able to fish the wire over (like I did) you will not be able to make the connection to the existing 7 pinn on the bumper. the plug adapter is wired in such a way that you cannot get your hand and the wire in the right orientation. The install of the unit will be less than an hour and probably closer to 30 min.
One last tip, when reinstalling the spare be careful not to push the tire to far to the front there is a thin metal shroud that the tire will rub on and squeak over every little bump. test it before you are done, ask me how I know. LOL
This harness is excellent. It plugged right in and looks like it should last a while. It also included plenty of zip ties and the necessary mounting screws. The hardest part was mustering up the nerves to drill a 2-1/8” hole in the bed of your truck. After drilling the hole, I put touch up paint on the bare metal to prevent rust. I also put silicone sealant in the screw holes, after they were tapped, to seal the metal there too. Install was quick and easy with the right tools; just the hole saw and a drill driver with the appropriate socket for the mounting screws.
As usual the ordering at etrailer.com was fast and easy. Shipment was fast and delivered on time. The 7way extension for gooseneck was as advertised. The toughest part of installation was feeding the end of the wiring harness through the post channel. Had one of these on my previous truck and missed it on my new truck. I recommend this product and etrailer.com
Gary
very easy to intall.the box it came in i was wondering if it was going to work the box was torn open
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Brooke M.
5/4/2024
I will make sure a customer service team lead gets a chance to look at this with you. Thanks for letting us know!