Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

See what our Experts say about this Hopkins Custom Fit Vehicle Wiring

• Instruction Manual Needed for a Tekonsha 2016 Hydraulic Brake Controller On a 1986 Ford F-250
  The wiring diagram for wiring your truck to your trailer can be found on our wiring page (see link). We also have a brake controller wiring diagram on our brake controller wiring page (see link). If you are wiring a 7-Way connector I would recommend the # ETBC7 wiring kit which has all of the wiring, circuit breakers and parts needed to install the 7-way once you have a 4-Way installed on the truck. If you need a 6-Way connector then the # ETBC6 wiring kit will be what you need. You can...
  view full answer...
• Recommended Trailer Wiring for 7-Way Trailer Connection and Brake Controller for 1986 Ford F-350
  For your 1986 Ford F-350, the factory wiring connector you need to start with is the Hopkins Plug-In Simple Vehicle Wiring Harness # HM40115. This custom-fit connector plugs into your Ford F-350's wiring harness, which is located beneath your vehicle along the driver's-side frame rail. Then you will need to use the Universal Brake Controller Wiring Kit # ETBC7 to utilize that 4-way connection and add the other 3 functions of reverse, 12v, and brake controller output. This kit will give...
  view full answer...
• Receiver Hitch Recommendation for 1986 Ford F-150 with Step Bumper
  The Curt Class IV Trailer Hitch Receiver, # 14001, is a confirmed fit for the 1986 Ford F-150 4-Wheel Drive with a standard or step bumper. This fully welded trailer hitch receiver bolts onto the F150's frame with no welding required. I am including a link to all of the hitches that we have available for a 1986 Ford F-150. Just select your bumper style and you will see a list of the hitches that are available for your truck. Each of those listed will also give you the recommended ball...
  view full answer...
• Trailer Wiring for 1986 Ford F-150 that Uses Spade Connectors for Connection
  For a 4-way wiring kit that fits your 1986 Ford F-150 that uses spade connectors you'd want the part # HM40115 which you can see the spade connectors in the attached picture.
  view full answer...
• Recommended Class IV Trailer Hitch Receiver For 1984 Ford F-150
  For a Class IV trailer hitch receiver on your 1984 Ford F-150, I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2" # 14001. This is a bolt on square tube design with a brlack powder coat finish over a protective base coat. If you have a deep drop bumper on your truck, then I recommend the Draw-Tite Trailer Hitch Receiver - Multi Fit - Class IV - 2" # 37130. This deep drop hitch is a bolt-on install with a round-tube design. It is black powdercoat over an e-coat...
  view full answer...
• Installation of 7-Way RV Connector on 1981 Ford F-250
  If your 1981 Ford F-250 already has a 4-way connector installed simply add etrailer"s Universal Installation Kit for Trailer Brake Controller, # ETBC7. This kit includes everything you need to install an electric trailer brake controller and 7-way connector. If your truck does not already have a 4-way flat installed, use the Hopkins Plug-In Simple Vehicle Wiring Harness, # HM40115 to install the 4-way flat connector first. Please note the linked product videos below along with a couple...
  view full answer...
• Parts Needed To Install 7-way Connector In 1984 Ford F-150 4x4
  The 7-Way Pre-Wired Car Connector, 7' Lead # 20023 you were looking at is designed to go in the bed of your 1984 Ford F-150 4x4 and splices in to the factory 7-way connector. If you do not currently have a 7-way connector you will need to add one starting with a 4-way connector # HM40115 and then add a 7-way connector using # ETBC7 which will plug into your newly installed 4-way connector and only require a few more connections which are as follows: Black wire to vehicle battery with...
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?