T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
Item # 118450
Retail:$44.17
Our Price: $32.13
Confirmed to Fit
2010 Chevrolet Malibu
excluding LTZ
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (410)
- Q & A (0)
- Photos
2010 Chevrolet Malibu - T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Trailer Hitch Wiring
- 4 Flat
- No Converter
- Tekonsha
Quickly and easily install a 4-way trailer connector on your Chevrolet Malibu with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required.
Features:
- Provides a 4-way flat trailer connector at the back of your vehicle to power your trailer's signal lights
- Compatible with 5-pole, 6-pole and 7-pole adapters (sold separately)
- Connects quickly and easily - no cutting or splicing of wires
- Locate connection points behind tail lights
- Plug in T-connector
- Constructed of 16-gauge bonded wire
- Comes with dust cap for 4-way flat connector
Specs:
- Maximum amperage: 7.5 amps per circuit
- 1-Year limited warranty
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the tail light assemblies to access this harness.
Once installation is complete, the 4-way flat connector will be stowed beneath your vehicle, near the trailer hitch. A mounting bracket (sold separately) is recommended to keep the connector secure.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
118450 Tow Ready T-1 T-Connector - 4 Wire
Installation Details
California residents: click here
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
Customer Reviews
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 118450
Average Customer Rating: 4.8 out of 5 stars (410 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required.by: Jose 04/13/2023
It was great because it fits perfect. T hankyou!!
by: Teresa K07/09/2012
2010 Chevrolet Traverse
eTrailer totally rocks! !! First of all, I only discovered your website as a result of trying to price a wiring harness for my vehicle. I had gone to the local store to get an estimate for installing a wiring harness on my 2010 Chevy Traverse, and was appalled that they wanted to charge me $79.99 for the wiring harness and then $100 labor!!! I couldn’t believe it – and went home and googled wiring harnesses, and I found your website among the search results. Right there on the page for my wiring harness was a 4-minute video with beautifully detailed instructions for how to install the harness on my vehicle.
Without hesitation, I ordered the part from your website, and days later I had it delivered to my door. I recently had knee surgery, so I enlisted the help of my 12-year-old daughter, who, after watching your instructional video, was ready to go... In no time at all, she had the wiring harness completely installed. Not only did she gain a sense of accomplishment, she also gained $10 to add to her piggy bank.
THANK YOU eTRAILER! I will be recommending you to everyone!
by: Peter06/10/2019
I purchased both a receiver hitch , Item # 75528 and the wiring harness. The hitch install would be like medium difficulty in my opinion! It required to drop the dual exhaust pipes so that you can move your tools in and around the hitch. Honestly it took several hours to loosen the rust that had build up throughout the years using wd40 and other things, so that the bolts that the hitch required for the install would fit! If it had been a new car with no rust, install would have been a breeze. The wiring harness, unfortunately, I misread the link the hitch recommended me to purchase! I called etrailer, girl said, It was a harness for a pre-existing manufacturers harness and so I had to replace it at my own expense! They recognized the issue and ordered the correct part. I received the new harness! It requires you to remove both rear break lamp housings! Got harness ran, when I realized the harness was short! I kept adjusting and checking to see if it was caught on something, but everything was fine. I got a revelation! The harness has cable ties wrapped around several areas of the harness! It comes like that from the manufacturer. I decided to cut one cable tie off and it stretch enough to reach the 2nd lamp housing. I used extra long cable ties, not supplied by supplier!, and tied any access harness to the tow hitch so that it isn’t hanging everywhere. But all in all it looks nice. Time consuming but nice.
by: phil04/07/2015
2009 Chevrolet Traverse
i bought the package, hitch,harness and ball mount. the harness took
a couple hours, i had trouble getting the taillight assembly out of
my traverse, no fault of the product. installation was easy and perfect.
i recommend this product to all.
by: Midwest Dad05/31/2024
Part arrived quick and ahead of schedule. The install was less than an hour. Highly recommend.
by: Charles05/05/2021
Watch the [online] videos on how to install & follow the instructions. The hitch & wiring harness install exactly as described. Couldn't have asked for an easier install.
by: Daniel 02/09/2024
KILLING THE GAME DAWG!
by: Tim H.03/04/2021
2011 Chevrolet Traverse
Extremely simple to install works great!!! This harness is worth the money!
by: Marty01/20/2014
2010 Chevrolet Traverse
etrailer staff went out of their way to get the shipment shipped out late tuesday. arrived Friday evening. The installation video made the installation a snap. Installed in about 30 minutes by removing the taillight lenses and cafefully routing wires away from exaust and tie-wrapped to hitch. First quality wiring kit for 2010 Chevy traverse. Saved time and money. I am very pleased and will make eTrailer my first call for my trailer needs. I couldn't be happier.
Marty
1/21/2015
The wiring harness for the trailer lights is working without any problems.Easy installation and fast shipping. it is well designed and has performed well in all weather.
by: Dave C.05/26/2014
2011 Chevrolet Traverse
I ordered the wiring harness with 5 to 7 day shipping and Jacob D. was able to get it to me earlier at the same shipping cost! The product arrived in great shape, was easily installed and I am completely satisfied!! I will definitely use etrailer.com again and recommend them to my family and friends. Thank you etrailer.com!!
Dave C.
Dave C.
5/26/2015
Product is still working great!
by: Jorge O.07/31/2012
2010 Buick Enclave
The product is very simple to install and easy to use. I will be towing a pop up camper with my Buick Enclave and what i liked most about this wire harnes is that i did not have to cut any wires on my car the plugs fit perfectely and i was able to install it with in 10 mins.
Dan W.
5/12/2014
Do you have a V92 towing package on your Enclave? I have a 2009 Enclave without a towing package and am looking to install a pop up camper as well. What is the weight of your pop up camper? What components did you install in order to tow the pop up camper? I just want to make sure I am not missing something. Thanks!
by: Lyle 02/28/2023
2012 Chevrolet Traverse
Very easy to install. Watched some videos and had no problems with installation.
Everything fit up perfectly.
by: Jessie T08/05/2016
2012 Chevrolet Traverse
Great qualoty and fast shipping. Trailer hitch and lighting for 2012 Traverse.
Jessie T.
12/18/2017
Its still doing great.
by: Sidney08/09/2018
2017 Buick Enclave
Ordered a hitch for my 2012 Buick Enclave in August of 2017. The fit was perfect. I also ordered the wiring harness adapter. The wiring and hitch installation took less than 2 hours. I’ve been using it for a year now and everything is still working perfect. This is the third car that I’ve used an etrailer hitch on and I couldn’t be more satisfied.
by: David01/26/2022
I can't say anything bad about the wiring harness for my trailer hitch. Along with the YouTube video that showed me how to do the install, this was about as easy as I can think it would be.
The connectors work perfectly - no issues with the brake or turn signal lights. The rubber cover for the connectors means that it is not dirty when I need to use it.
by: Lonnie11/02/2014
When I first installed the wiring harness the passenger side rear turn signal would not operate. This caused a number of other malfunctions, e.g. the ignition key could not be removed, the power windows would not operate, the power sunroof was inop., etc. It confused me as I did not know what had occurred to cause all these things to go wrong. After some online research I found that somehow the fuse had blown and caused all of the related malfunctions. Upon replacing the fuse all was well. I subsequently hooked onto a rental trailer, towed it near 1,700 miles and hitch and wiring system worked perfectly. In summary, even after an initial scare and anxiety over the blown fuse, I would definitely recommend your products.
by: Henry E09/28/2015
2012 Chevrolet Traverse
The Tekonsha t - one connector write harness was so easy to put on. Only took me about 15 mins all together. Shipping was very fast product works great.
Henry E.
9/27/2016
the custom fit vehicle wiring harness works perfectly. No problems installing it, and no problems since. I have actually showed it off and showed how it is hooked up and got a lot of compliments on it especially for ease of installation.
by: lester bickel07/28/2014
The towing light harness came shipped quickly. It is installed and working well. Katie was very helpful.
Lester B.
7/28/2015
The tow package has been used many times, and it is still working well.
by: Gary05/23/2015
Great product! Was easy to install using the etrailer.com YouTube video. High quality product and a fair price. Couldn't be more pleased.
Gary
5/26/2016
Still works great and I would buy it again. Very pleased a year later with this purchase.
by: Brian Mc06/26/2013
2012 Chevrolet Traverse
I have ordered from eTrailer before. Everything I have ordered from them has shipped fast and packed well. I also have seen their YouTube video's for installation on this hitch and wiring harness and that was what sold me on buying from them. It only took around 20 minutes or so to put this hitch and wiring harness on. Fit on our 2012 Chevy Traverse is excellent and until you remove the plastic hitch cover on the bumper you cant see it. I put a receiver hitch on all my vehicles and this has to be the easiest installs I have every done.
by: Nathan W.06/11/2014
2011 Chevrolet Traverse
I received the harness to wire my 2011 Chevy Traverse to tow my cargo trailer. The product came quickly, was well packaged, and the wires seemed durable. The harness plugs into the tail light connections so no splicing or any other electrical work is required. A screw had to be drilled into the sheet metal to ground the lights but that’s the only real work required other than removing and re-installing the tail light fixtures. After watching the installation video produced by eTrailer, I went out and had no issues installing the product. Excellent video! The product is great, but the best thing for a DIY install is the video demonstrating the installation. Excellent video and easy to install product.
by: Pat C.06/05/2018
2008 Buick Enclave
2008 Buick Enclave - Trailer Wiring Kit - My vehicle had a tow hitch but no wiring When I purchased years ago. Install completed by 60 yr old female - was a bit hesitate to order online since I was clueless as to what I needed or how to install. Watched video looked “dummie proof”. Took a chance , kit arrived in reasonable time, was as simple as was depicted in video. 20-30 minutes , screwdriver and I had it installed, ready to tow. I am thrilled to have a product that is true to advertising. As most of us have experienced, not all companies are honest in their marketing. etrailer has earned my respect and humble gratitude for being an honest and reputable company and I will not hesitate to use again and also refer to friends and colleagues . Thank you, May God continue to bless you!
by: Forresthttps://webmail.centurylink.net/mail05/13/2019
Buick Enclave
Hitch and wiring harness arrived well packed and complete. The installation went great, exactly like the instructions and completed in less than an hour! Used it the next day with no problems. This is a great addition for my Buick Enclave allowing us to do minor hauling around home and added storage space on trips. The quality of the hitch exceeded expectations, good work!
by: Holly 02/23/2020
Chevrolet Traverse
Was very easy to install after you turning how to remove my vehicles tail lights. Have used many times to pull my boat and atv trailer. Plug has worked every time and is still in great shape. Installed it in a Chevy traverse that I installed a after market hitch on.
by: sscsksl04/15/2016
2009 Chevrolet Traverse
This is a quality well built product. i know this for two reasons. i have installed about eight differnt brands over the years. the second reason is a bit unusual. i intalled this one twice. months after installing the hitch and harness my wife got into an front and rear collision. Everyone was fine but insurance totalled the vehicle. i removed the hitch and harness and reinstalled it on a newer model Traverse. This time i had a buddy hold one side while i started the bolts. Otherwise both are easy great products.
25
410
Show More Reviews
See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring
- Trailer Wiring Harness Kit Options for 2011 Chevrolet TraverseCurt 4-Pole trailer wiring harness kit # C56245 fits the Chevrolet Traverse for model years 2013 through 2017. For your 2011 Traverse we do offer similar plug-and-play wiring kits and the correct one will depend on how the car is equipped. If you have the factory tow package the car will have a round U.S. Car connector under the rear bumper that will accept a 4-pole plug-in harness # 118384 or a combination 7-way/4-pole harness like # HM40975. If the car does NOT have the factory tow...
view full answer... - Parts Needed to Install a Brake Controller in a 2011 Chevy TraverseFor a brake controller for your 2011 Chevy Traverse I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. Since you do not have a 7-way harness you will need to first start with a 4-way. For that you would want the part...
view full answer... - Which Trailer Connector is Needed for 2009 Chevy Traverse without Tow PackageThe trailer connector you need will depend on the type of trailer you are planning on towing and whether or not your Traverse is set up with factory tow package wiring. If you are going to tow a smaller utility or flat bed trailer that does not have electric brakes or on board accessories that would require power like an electric jack or interior lighting, then a 4 pole connector should be just fine for you. To provide a 4 pole connector on your Traverse without factory tow package wiring,...
view full answer...
- Hitch, Ball Mount and Wiring Harness Options for 2012 Buick Enclave Without Factory Tow PackageFor your 2012 Buick Enclave the Draw-Tite 2-inch Class III hitch # 75528 is a confirmed fit. Install instructions and a complete install video are linked for you. The hitch comes with all needed hardware. You will also need a ball mount, hitch ball and pin/clip. I suggest ball mount # 989892. In terms of the wiring harness options you ask a very good question. The available products, non-powered models # 118450 and # C56027 and the powered converter model # HM11141615, differ in one important...
view full answer... - Ease of Installation for the etrailer e98863 Hitch on a 2008 Buick EnclaveThe etrailer Trailer Hitch Receiver item # e98863, for a 2008 Buick Enclave, has a three out of ten on our difficulty to install scale. It looks like a pretty simple installation there's no cutting or trimming required. You will have to temporarily detach one of the muffler braces so I recommend having your Enclave sitting for awhile where you are going to install the hitch so the muffler and surrounding area isn't hot. I have linked the instructions and also a couple of install video's...
view full answer... - Trailer Wiring Harness for a 2009 to 2012 Chevy TraverseThe Tow Ready trailer wiring harness # 118450 is designed to fit all models of the 2009 to 2012 Chevy Traverse. I have included a link to a video showing installation on a 2012 Traverse for you.
view full answer... - Recommended Hitch and Wiring Harness for a 2011 Chevrolet TraverseI would be happy to help you set your 2011 Chevrolet Traverse up for towing. You are going to need a hitch receiver, a couple of wiring harnesses, a brake controller, and a ball mount. Let's start with your hitch receiver I recommend the etrailer Trailer Hitch Receiver item # e98863. This is a custom fit hitch that bolts directly to your Traverse with included hardware. It has a maximum gross trailer weight of 5,000 lbs and maximum tongue weight capacity of 500 lbs. I have linked an installation...
view full answer... - Is Drilling Required To Install Curt Trailer Hitch Receiver # 12051 On My 2011 Chevrolet Malibu LTTo install the Curt Trailer Hitch Receiver, part # 12051, on your 2011 Chevrolet Malibu LT you will need to drill 2 holes that are 17/32 of an inch. There is a template included with part # 12051 so that you drill in the correct spots. All of the hitches available for the 2011 Malibu require drilling to install. A drawbar, pin and clip come included with part # 12051. To complete your towing setup, you may be interested in the following: Wiring, part # 118450 1-7/8 Inch Hitch Ball, part...
view full answer... - Trailer Hitch and Wiring for 2011 Chevy Traverse LTThe answer is going to depend entirely on the fully loaded weight of the food trailer and if your 2011 Chevy Traverse LT has the trailer towing package. I looked up a copy of the owner's manual and it states that a 2WD can pull a trailer that is a maximum of 2,000 lbs UNLESS it has the V92 Trailer Towing Package. If it does the maximum trailer weight is 5,200 lbs; if you are unsure if your '11 Traverse has the towing package you can call your local Chevy dealer with the VIN and they will...
view full answer... - Will Trailer Wiring Harness from a 2012 Chevy Traverse Fit a 2015 Chevy TraverseThe trailer wiring harness you have now for the 2012 Chevy Traverse is # 118450. It only fits up to 2012 models. The 2013 model year had some changes that continued in the 2014 and 2015 models which is why the wiring harness for the 2012 models will not fit the 2015 models. For a 2015 Chevy Traverse that did not come with a factory trailer connector you can use Curt harness # C56181.
view full answer... - 4-Pole Trailer Wiring Harness for 2013 Chevy Traverse LTZ AWDFor your 2013 Chevy Traverse, you'd want to use the part # 118270 trailer wiring harness. In addition to the wiring harness, the fuses and relays needed to activate the trailer illumination wiring portion of the tow package are included. If you click the provided link, you an see the installation instructions as well as an install video. The # 118450 you referred to fits Traverse models up through the 2012 model year, and wouldn't work on your 2013 Traverse.
view full answer... - Parts Needed to Tow Trailer with 2012 Buick EnclaveFor a trailer hitch for your 2012 Buick Enclave the Draw Tite hitch part # 75528 is a confirmed fit and will work well. I attached an install video for more info on this. Then for trailer wiring all you'd need is the # 118450 to provide you with a 4-way. The part # 118384 would be the correct kit if your vehicle came with a 7-way and you needed to convert it to a 4-way but it sounds like you don't have the 7-way wiring at this time. If you wanted to do some towing you might be interested...
view full answer... - Recommended Towing Set-up For 2009 Chevy Traverse To Tow 5500 lb Travel TrailerFor your 2009 Chevy Traverse, lets start at the very beginning so I can walk you through parts needed. If you do not have a trailer hitch receiver, I recommend the Draw-Tite Class III # 75528. This is a very strong hitch that will meet your towing needs. If you don't have a ball mount, I recommend using the etrailer.com ball mount kit # 989900 that will give you different rise and drop options along with different hitch ball options to tow a trailer level. For vehicle wiring to tow...
view full answer... - What Hitch On 2009 Buick Enclave Will Allow The Rear Fascia Door To Be UsedThe hitch I have for your 2009 Buick Enclave that will allow you to reattach the fascia door after the hitch has been installed is the Curt Trailer Hitch, # 13424. It is a bolt-on installation, no drilling required. I am sending a link to the installation instructions for that hitch. As far as the fascia door with a bump for factory hitches working on the other hitches, I called my supplier on the Draw-Tite Hitch, # 75528, and the Hidden Hitch, # 87435, and they said that you would need...
view full answer... - Trailer Wiring Harness for a 2011 Buick Enclave without Factory Installed 7-WayThe replacement 7 and 4-Way trailer connector # HM40975 is designed to replace a factory 7-Way if your 2011 Buick Enclave came with one from the factory. If your Enclave did not come with a factory installed trailer connector and you want to add a 7-Way you would first need to install a 4-Way, # 118450. After the 4-Way is installed to add a 7-Way you would either need adapter # 37185 (if you do not need the electric brake or 12 volt functions to work on the trailer), and plug in the 4-Way...
view full answer... - Transmission Cooler for 2011 Chevy TraverseI would start by determining the towing capacity of the vehicle. I did some research, and saw a range of 2000-5200 lbs depending on how the vehicle was equipped. If you phone your Chevy dealer, they should be able to tell you the towing capacity of your Traverse based on its VIN. If you find that the fully loaded and ready to tow weight of the boat and trailer does not exceed the towing capacity of the vehicle, the only other thing I would consider essential would be an aftermarket transmission...
view full answer... - Can Fascia Door Be Reinstalled after Draw-Tite Hitch 75528 is Installed on 2010 Buick EnclaveOnce installed, the front face of the receiver will extend a bit too far rearward in order for the fascia door to be reinstalled. From what I have been able to determine in my research, the other fascia door you mentioned (with the hump in it) can be obtained from your Buick dealer, but it is intended to work with the OEM hitch because the aftermarket hitch receiver tubes extend a bit further rearward. So, you can install an aftermarket hitch and leave off the fascia door, or purchase...
view full answer... - Parts Needed to Mount a Hitch and 4-way Flat Connector on a 2012 Chevrolet TraverseThe Draw-Tite Max-Frame Trailer Hitch Receiver # 75528 does include the mounting hardware. The T-One Vehicle Wiring Harness # 118450 can be mounted to the hitch using the Mounting Bracket 4-Pole Flat # 18144 and the No-Drill Mount for Electrical Mounting Bracket # 18140. If you are needing replacement hitch mounting hardware, we do have that available as the Replacement Hardware Kit for Trailer Hitches # RHK. You would just need to select Draw-Tite in the manufacturer tab and put the hitch...
view full answer... - No Green Light On the Power Trac Brake Controller When Trailer is Connected to a 2011 Chevy TraverseThe Electric Brake Controller Wiring Adapter, # 3026-P, is designed for use with the 2011 Chevy Traverse, if it has a factory installed 7-Way connector. Since you have a aftermarket 4-Way connector, like part # 118450, installed inline with the taillights and a 7-Way adapter, like part # 37185, that the 4-Way harness plugs into, you most likely will have to run at least one wire from the blue brake controller output wire to the blue electric brake feed wire on your 7-Way adapter at the...
view full answer... - How to Install 7-Way Trailer Connector and Brake Controller on a 2011 Buick EnclaveHow you'll proceed will depend on if the trailer has brakes or not. Usually, the fact that a trailer uses a 7-way indicates that the trailer has brakes but that's not always the case. If the trailer doesn't have brakes, you'll first install the # 118450. This provides easy access to the taillight circuits without needing to cut and splice into any wiring. You'll then install the # 37185 adapter that will convert the 4-pole to a 7-way connector. The adapter will plug directly into the 4-pole...
view full answer... - Can Rear Fascia Panel be Replaced After Installing Curt Trailer Hitch # 13424, 2011 Chevy TraverseYou will notice in the instructions that I have linked for Curt Trailer Hitch, # 13424, that it states that the panel in question may be reinstalled on some models. So I spoke with my contact at Curt to determine if the 2011 Chevy Traverse was a model that it could be reinstalled on. He stated that they did not have information on the 2011 but on the 2010 it can be reinstalled. Basically, if the rear fascia is the same on the 2011, then it will fit. But if it has been redesigned, it will...
view full answer... - 4-Way Trailer Connector Recommendation for a 2011 Chevy TraverseIf you have a round trailer connector harness under the bumper of your 2011 Chevy Traverse the part # C55515 would work as a 4-way harness. If you can't find that connector you would use the part # 118450 for a 4-way harness. If you need to order something right now this harness would fit regardless of your setup.
view full answer... - Availability of a Replacement 4-Way Vehicle Side Plug End I have a solution for you. The Hopkins Wiring Harness, # HM48035, will replace the malfunctioning 4-flat plug on your vehicle. You will just need to cut off the current plug and using Deka Heat Shrink Butt Connectors, # DW05744-5, connect the new plug to your wiring harness.
view full answer... - Hitch Solution for 2010 Chevy Malibu that Allows Transporting Dirt BikeAll of the hitches we offer for your 2010 Chevy Malibu are going to be too light duty to carry a motorcycle carrier. Motorcycle carriers require the 2 inch hitch size and for smaller vehicles like yours there are only 1-1/4 inch hitches available like the Draw Tite part # 36479. With your vehicle best solution would be to tow a small trailer. To do that you'd also need trailer wiring like the Tekonsha kit part # 118450 as well.
view full answer...
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Nicholas E
Test Fit:
Rick A
Test Fit:
Brent H
Expert Research:
Mike L
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Reno H
Expert Research:
Jameson C
Video Edited:
Andrew K
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Andrew L
Video Edited:
Kathleen M
Video Edited:
Chris R
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jose
4/15/2024
After a year using t-wire in the summer and winter season I have not had any problems, everything is like a professional.