What Hitch On 2009 Buick Enclave Will Allow The Rear Fascia Door To Be Used
Question:
Hello. I am looking at a hitch for the above vehicle that will allow the fascia door to be re -attached. Or one that will allow me to use the fascia door for factory hitches it has a bump to allow for clearance of the hitch thanks
asked by: Rex M
Expert Reply:
The hitch I have for your 2009 Buick Enclave that will allow you to reattach the fascia door after the hitch has been installed is the Curt Trailer Hitch, # 13424. It is a bolt-on installation, no drilling required. I am sending a link to the installation instructions for that hitch.
As far as the fascia door with a bump for factory hitches working on the other hitches, I called my supplier on the Draw-Tite Hitch, # 75528, and the Hidden Hitch, # 87435, and they said that you would need to check with the GM dealer if that fascia door would fit.
If you are going to be towing with this hitch you will also need a Ball Mount, # C45010, a Pin and Clip, # PC3, and a hitch ball. The hitch ball you need will depend on what size the coupler is on the trailer you will be towing. If it is 1-7/8 inches coupler you will need Tow Ready Hitch Ball, # 19260. If it is 2 inches then you will use Tow Ready Hitch Ball, # 19247.
The wiring harness you would need would be Tow Ready T-One Vehicle Wiring Harness with 4 Pole Trailer Connector, # 118450, which connects behind the vehicles taillights. It simply plugs in and there is no cutting or splicing of the wires. I am sending a video link of the wiring harness being installed on a 2009 Buick Enclave.
![Jeff D](https://images.etrailer.com/static/images/catg/people/338_tn.jpg)
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >