Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
(218 reviews)
Price: $202.85
In Stock
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
Item # HSSF
Retail:$220.09
Our Price: $202.85
You Save: $17.24
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (218)
- Q & A (0)
- Photos
- Used (1)
Brophy Truck Camper Tie Downs - HSSF
- Front and Rear Tie-Downs
- Bed-Mounted
- Powder Coated Steel
- Brophy
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.
Features:
- Creates attachment points for securing your camper to your truck bed
- Wide clamps provide superior holding strength
- Turnbuckles (sold separately) required to attach camper to tie-downs
- Protects your truck's paint with neoprene pads attached to the brackets
- Resists corrosion and rust with black powder coated steel
- Clamps securely onto your bed rails - no drilling required
- Includes 4 camper tie-downs with clamp plates, 12 neoprene pads, and installation hardware
- Made in the USA
Specs:
- Application: for exact fits, enter in your vehicle's year/make/model above
- Minimum 2" needed between sidewall and lip of bed rail
- Not compatible with drop-in bed liners, aftermarket bed rails, double-walled beds, or side-step beds
- Dimensions: see diagrams below
- 1-Year limited warranty
No-Drill Installation
These clamp-on tie-downs install quickly and easily, with no drilling or modification to your truck required. Because they're mounted in the bed instead of on the frame or body of your truck, you don't need any kind of fancy mechanical background to get this job done. You just need to slide the hold downs over the rails of your truck and clamp them down with the included T-bars and hex bolts.
The fact that they simply clamp on means that you can remove these tie-downs when you're not hauling your camper, leaving no trace. Use the provided neoprene pads on the T-bolts and tie-downs where they make contact with your truck to make sure no scratches or dents will be left behind either.
It's important that the tie-downs on your truck line up with the anchors on your camper at the correct angle to ensure a secure hold. Ideally the tie-downs should be on the outside of your camper's anchor points, but they can be on the inside as well, just as long as they're not lined up with each other.
Securing your Camper
To secure your camper to your truck, you'll also need a tie-down hardware package consisting of turnbuckles, S-hooks, and chains (TDHP - sold separately). This hardware attaches the anchors on your camper to the tie-downs on your truck to keep your camper safely mounted. Once you tighten the turnbuckles to the correct level of tension (not too tight!), you'll be good to hit the road.
HSSF CR Brophy Truck Camper Tie Downs for Slide In Truck Camper - Camper Hold Down - No Drill Tie Down - 4 Pack
Installation Details
Customer Satisfaction Score:
90% were satisfied with this product
10% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4 - HSSF
Average Customer Rating: 4.6 out of 5 stars (218 Customer Reviews)
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.by: TheAvionNomad01/18/2024
I used these to mount a vintage 1970 Avion C-11 to a 1993 D250. They worked great and were much stronger than I expected - and it was a huge cost savings (and a much more attractive look) than some of the frame mounted options of more than $1000. There were some oddities that I noticed. It was impossible to mount them exactly the way the instructions suggested because of where on the wings near the cab,. The brackets also could not stay on with the camper unloaded because they would hit the jack mounts, meaning they had to me bolted in after the camper was in the truck but before lowering the jacks, making the access to the bolts a frustrating 'feel for it' experience.I'f suggest the manufacturer secure the bolt so that you don't need to hold both sides when tightening/loosening, and also refine it to need less turns to do so. It took me 2 hours to mount the first time, and not much less when removing them with the limited access. The pads also came off in the first use.
I gave it a 5 star because I realize there are limited options for older campers and anything universal is going to have issues with some thing - so that's just my input and experience. Overall pretty reasonable for the price and functionality.
by: Pat03/20/2023
The product was shipped extremely quickly, it arrived 3 days after I ordered them. As far as the product goes I was extremely pleased that they were as easy to install as the product video showed them to be. I had been looking for
a tie down system that would work for my 2018 Ford since I purchased my camper in 2020 and after much research I found these at etrailer. One word of advice is that if your camper has a shower or other design that allows the camper to extend across the bed behind the wheel wells, either move the rear tie downs forward or shorten the leveling stud before you attempt to load your camper. On mine it turned out that once the tie downs were placed and attached I had to cut off about 3 inches of the threads.
Other than that it was an easy install although the bolts that attach the tie downs to the under lip clamp are a challenge to install but take your time and they will go on. I will post an update once I have been on the road for a few trip and see how they are working.
Thank you etrailer for your super fast shipping and online product videos.
by: Ed B.05/21/2019
Purchased the Brophy camper tie down set of four for the Palomino truck camper I just purchased. These are my second set as the first set were sold with my Hallmark camper. Easy to install and hold the camper in the truck with no worries.
by: James 05/20/2024
Ordered these for new camper. Very easy to install and does the job without the high cost of frame mount.
by: Jeff Smith10/22/2023
These tie downs work great. It holds my 3k lb Cabover camper in place without issues. And I live in my camper, so not losing my home is very important to me!!
by: Shelly12/13/2023
The products arrived on the time scale as stated. The packaging did not hold up and the box with the metal tie downs was broken open. There was too much weight for the box and it just split open. Not sure if anything is missing. Packaging of items that are heavy should be more secure and sturdy.
Jenny N.
12/14/2023
Oh no! I will have our Customer Service team reach out to you. If anything is missing we can take care of it.
by: Ron W07/02/2016
As far as I'm concerned these are junk. Wasted my money. Do not mount in proper location on a 2011 Chevy Silverado 6.5' Bed. Because of the design of the bed rail the mounts cannot be installed in the proper locations for securing camper. The photos show the maximum forward and back that these can be mounted. Not at all made for the 6.5 foot bed 2007 or later Siverado. The Black Powder Coated Steel isn't that great either. Paint missing, dinged up from storage and shipping probably.
by: Allen.08/22/2022
These wont work for my truck and camper. The box on a 2018 gmc 2500 short bed does not lend well to placement of these in order to get the correct geometry i needed for the tie-down points on my Palomino maverick 6601. I had high hopews of not having to buy the frame mounts, but i will have to.
Mike L.
8/31/2022
The HSSF tie downs have specific fit parameters as mentioned in the product specifications above: External bed rail width cannot exceed 5-12 Requires at least 2 of space beneath lip of bed rail Not compatible with -in bed liners, bed rails, double-walled beds, or side-step beds
Allen.
8/23/2023
In response to the etrailer comment response, they fit on the bed fine, with plenty of clearance and would work for a smaller camper. they just did not fit in the right spots for my truckcamper combo.
by: . George01/03/2024
The tie downs are great no problems.Very easy to install.I keep them on my truck all year long Thank you
by: Terry08/08/2023
Order arrived quickly, priced ok. Box was broken open by shipper NS the 4 T-bolsts bolts ere missing. Etrailer shipped ou the missing parts a few days later, but in the meantime I fashioned t-bolts I could use for my trip. Many customer comments on this camper Brophy tie-down match my experience. Etrailer follow up was great, but surely must be aware that their packing is sub-standard. Perhaps zip-tying the T-bolts to larger pieces would eliminate the loss even in case of breakage. Functionally the tie-dows were easy to install and seem quite adequate for off-road use of my in-bed camper. Will continue to use etrailer because of their excellent customer service.
by: captkirk02/15/2021
These tie-downs worked awesome for our pop up camper on our 1998 F150. Super snug, haven't loosened up or moved on the truck, camper hasn't budged either. I was leary at first not having the camper tied to the frame but now I have total faith in these tie downs.
by: Mike S05/23/2020
These Brophy tie downs have worked great over the past year. I leave the camper on the truck and it is my daily driver as well as RV. The camper weighs in at 1500 dry and about 2000 loaded. I do not do any radical 4x4 but I have taken some backwoods off road logging trails.
by: Bing09/23/2019
I received this tie downs on July, and first used it yesterday.
My Camper ‘s dry weight is about 1600 lb, and the products are good for my truck camper.
The problem was the position where tie downs were fitted on my truck. I tried several times to fitted tie downs to my truck.
by: Brent 08/08/2019
I bought these for our brand new 2019 GMC Sierra 1/2 ton because no custom options were available. I was happy that they were easy to install, and look great. I’ve used them in the past and have been happy with how they hold campers. Sure I’d rather have custom mounts from the frame, but for the price and because these are my only option that’s what I got. These will work just fine, and I like that I can swap these out on trucks.
The one thing I wish was different was that the threaded T handle portion would have a longer option. I had to fancy up a 2”x6” to run inside the side of my p/u bed so they would touch something.
As always another great shopping experience with etrailer. They haven’t let me down yet. Especially Lori, what a great customer service rep.
by: Patrick04/02/2020
These things are solid although i put duck tape on the T pads....installed 2014 Chevy Silverado 6.5 ft bed for 1200lb Starcraft.
Patrick
4/6/2021
Still have not moved! Great design and cost savings.
by: Matt04/14/2015
These camper hold-downs appear to be manufactured from good steel stock and should do the job nicely. I did have one piece that was slightly damaged but was not caught when packaged (the damage was not due to shipping). I was able to take a hammer to the bent steel and straighten it sufficiently to use the part. It was a little disappointing however, and should have been caught prior to shipping.
Overall I am pleased with the quality and price
by: Regan06/25/2019
Using on 2013 Ford F150 for a smaller cabover. Great quality product, shipped fast, works great. Had to turn bolts around to clear inside of bed. Held camper solidly over rough trails!
by: Bryce05/10/2022
Fits well on a First Gen Tundra. I was extremely unsure about fitment for my truck but they work great! Install only takes 5-10 minutes. I would definitely recommend. Steel is quite thick and seems very strong.
by: John05/25/2020
Easy to install and have done what’s expected. Keep the camper in place!!
by: JAMES K09/24/2012
ORDER ON TUESDAY RECIEVED ON FRIDAY NOON SAME WEEK ONLY PROBLEM WAS 4 7/ 16 NUT WERE 4 1/2 NUT HAD TO BUY 4 NUTS OTHER THEN THAT I WOULD BUY OFF ETRAILER AGAIN VERY GOOD SERVICE
by: Neil08/04/2021
Arrived on a rainy day with the box falling apart. Too much heavy steel to be loosely packed. Fortunately, the hardware bag was still there. Some bare metal showing. I had some emails with MacKenzie B. and they were responsive and without asking they offered me a 5% refund for the damage. After my first trip, they performed well on some very bumpy roads. Held strong and didn't move. I did have to re-adjust the lower standoffs after the first week. Taking them on/off is frustrating because the 2 nuts are in the small gap behind the clamp against the inner bed wall. Too tight for all but an open end wrench. 1/6 turn times too many fumbling tries, arg! Also, I was nervous not having a locking feature (lock washer, locknut, etc). I bought 8 locknuts (pinch type) and welded them to the inner plate. Then bought 8 round head hex bolts (grade 8). So now I can install easily with an Allen socket. See pictures. Recommend eTrailer consider this modification.
Neil
8/5/2022
After my mount bolt mod, Ive used these multiple times and they are working great! Very stout and no visible marks on my F250 bed.
by: Chuck11/13/2012
Found easy to install, I placed lock washers on the 8 3/8" bolts. Sold at Menards for 89 cents (pkg of 8) not in kit. Placement was a little restrictive with dealer installed bed liner. Takes 30 minutes to install all 4. Great buy.
by: Jason S.06/05/2019
These tie downs were a great budget solution in leu of a permanent installation of my camper shell and/or frame mounted tie downs. Aside from needing to plan their placement (they can hang in front of the gas cap if you don't plan it right the first time around... no, I didn't accidentally block my gas cap... maybe I did) and take into consideration they also need a little bit of internal clearance as well, they work just fine. I haven't noticed any cargo shifting nor warping of the truck bed around where they are installed. My camper shell is under 1K lbs and it holds just fine.
Jason S.
6/8/2020
A year later & they still hold strong.
by: Dayton12/15/2023
Awesome customer service my new fav pl ace
by: dave07/08/2016
Its a good product for a light camper. I personally would not use it on anything heavier than 1000lbs. But then iam not an engineer. I sold mine and my camper and bought frame mounted tie downs
Dave
7/11/2017
Did not work for me. Tried to send them back but shipping would cost a bundle so i would get less than half of what i paid. Sold them same day on-line. Not good for a larger camper.
Rachael H.
7/12/2017
25
218
Show More Reviews
See what our Experts say about this Brophy Truck Camper Tie Downs
- Camper Tie-Downs When Running Boards Under BedSince your running boards are also under your bed you will need to use Brophy # HSSF Bed Mount Tie-Downs that install in your stake pockets. You will also need the Brophy # TDHP basic turnbuckels.
view full answer... - Fitment of Brophy Clamp On Camper Tie-Downs on a 2019 Ram 3500 and 2018 Palomino BackpackThe Brophy Clamp On Camper Tie-Downs # HSSF is a universal application and should work great to secure your 2018 Palomino Backpack camper on your 2019 Ram 3500. Just reference the attached dimensional photo to ensure that it will accommodate the side rail on your pickup and you are good to go!
view full answer...
- Camper Tie Down Recommendation for a 2014 Ram 1500 with Running BoardsI have a set of camper tie downs that will fit your 2014 Ram 1500, but they attach at the stake pockets of the bed and not the frame like the Torklifts do. There is no Torklift option for your truck if it has running boards. The Brophy Camper Tie Down, part # HSSF is a universal fit item and will work on your 2014 Dodge Ram 1500. The Brophy Tie Down mounts over the sidewall of the truck bed. The recommended hardware kit to install part # HSSF is Camper Tie Down Hardware Package, part...
view full answer... - Camper Tie-Down Recommendation for 2005 Dodge Ram 2500We do offer Brophy tiedowns that will fit your 2005 Dodge Ram 2500 as long as it does not have a stepside bed or dual rear wheels. The Brophy tiedowns that will work for your application is part # HSSF. The hardware kit you would need to attach the tie-downs to the camper is the part # TDHP.
view full answer... - Which Camper Tie Downs From Brophy for 2012 Nissan TitanBrophy tie downs, # HSSF, will work well for your 2012 Nissan Titan. The Brophy tie downs don't have a specific vehicle fit list but this is the kit we've found works best on import truck beds. This setup is rated for use with any camper that fits the bed dimensions of your truck so it would work well with yours. I also recommend hardware package # TDHP to secure the camper to the tie downs.
view full answer... - Truck Bed Camper Tie-Downs for 2007 2500Chev Crew Classic According to my contact at CR Brophy, the # TDSF stake pocket camper tie down isn't compatible with your truck. The # HSSF clamp style tie down will work as long as your truck bed has two inches of available space under the truck bed sidewall as shown in the provided diagram. You'd also need the hardware package, part # TDHP which includes the chains, turnbuckles and hooks to connect the tie-downs and the camper.
view full answer...
- Recommended Clamp On Bed Mounted Camper Tie Downs for a 2001 Dodge Ram PickupFor a set of clamp on camper tie downs that have been confirmed to fit your 2001 Dodge Ram Pickup I recommend using the Brophy Clamp On Camper Tie-Downs part # HSAB. I have attached a photo for you on a truck from the same generation to show fit. The Brophy Clamp On Camper Tie-Downs part # HSSF should also fit but we have not yet tested this. It looks like you may need the angled lip to clear the bed sides so I do recommend using part # HSAB. The angled lip is the only difference between...
view full answer...
- Why are Frame Mounted Camper Tie Downs for 2018 Ford F-250 More ExpensiveBrophy has a stake pocket mounted tie down setup that fits your 2018 Ford F-250 short bed with the part # HSWB but the # HSSF you referenced is not listed as a fit. Stake pocket tie downs are more universal in the trucks they fit, are a simpler design, and not quite as secure as the frame mounted styles which is why the cost of them is lower. They work but in general people prefer the frame attachment style since it's a much more secure attachment as the frame of the truck is much stronger...
view full answer... - Will the Brophy Camper Hold Downs Fit a 2012 Chevy Silverado 1500 with 6-1/2 Foot BedIf it is not a dually and does not have a step side or double wall bed, then the Camper Hold Downs, # HSSF, will fit your 2012 Chevy Silverado. These hold downs wrap around the bed rather than fit inside the stake pockets and will work for any camper that is a correct fit for your vehicle. You can also use camper tie down hardware kit, # TDHP, with the hold downs. To install, first place the protective tape under the rest plates and on the T-Bars. Next, thread the T-Bar into the nut at...
view full answer... - Camper Tie Downs for a 2005 Dodge Ram DuallyThe Brophy camper tie downs, # HSSF, fit most domestic full size trucks, but there is not a specific vehicle list that they will fit. You will have to go by the measurements of the tie downs and the installation instructions to determine if they will fit your 2005 Dodge Ram Dually. I have included some pictures that should help. We also have some stake pocket mount tie downs that could fit, # TDSF. With either tie down kit, you can use the Camper Tie Down Hardware Package, # TDHP.
view full answer...
- Camper Tie Downs for a 2006 Ford F-150 SupercrewThe measurements and requirements of the hold downs and the bed sides on a 2006 Ford F-150 are not compatible so you that is why you cannot use # HSSF. You may be able to use stake pocket mount tie downs # TDSF. Take a look at the instructions I have linked and compare them to your truck to ensure fit. With this tie down kit you can also use tie down hardware # TDHP.
view full answer... - Fit of Brophy Camper Tie-Downs HSSF on 2002 Ford F-350 Crew Cab Long-Bed Diesel You can use the Brophy Clamp On Camper Tie-Downs # HSSF with your 2002 Ford F-350 crew cab long-bed diesel so long as the truck does not have a drop-in bed liner, plastic rail caps, a double-walled bed or a side-step bed. You also need to have 2-inches of space beneath lip of bed rail. Please refer to the linked cross-section diagram and to the video that show how the tie downs install.
view full answer...
- Availability of Chrome Plated Camper Hold Down ClampsYes, we can supply Camper Hold Down Clamp - Chrome Plated, # HSCP. These clamps are the chrome plated version of the HSSF hold downs.
view full answer... - Will The Brophy Camper Tie Downs # HSSF Fit My 1999 Ford F-250 Super DutyThe Brophy Camper Tie Downs, part # HSSF, are a universal item for domestic full-size trucks and will fit your 1999 Ford F-250 Super Duty. The # HSSF tie downs can be used on any size camper. If your truck has a drop-in bed liner, it will need to be trimmed or removed to use part # HSSF. The recommended hardware kit is the Camper Tie Down Hardware Package, # TDHP.
view full answer... - HSSF Stake Pocket Tie Downs for 2011 Ford F150According to Brophy, the HSSF Camper Tie Downs will fit your 2011 F150 unless it has a double wall bed. The tie downs do not actually attach using the stake pockets, but would clamp to the underside of the bed rails as shown in the provided photo. If you do not have the tie down hardware, you might also be interested in part # TDHP.
view full answer...
- Quantity Of the Brophy Camper Hold Downs Come with the # TDSF # HSSF and # HSABAll of the Brophy Truck Bed Camper Hold Downs like the # TDSF, HSSF, and the HSAB are sold in a quantity of 4.
view full answer... - Brophy Camper Tie Downs for 2015 Chevy Silverado 3500 Single Rear WheelI do have a solution for you, but the Brophy Stake Pocket Mounted Camper Tie Downs # TDSF are not designed to fit on 2011 and newer pickups, so they will not work for your 2015 Chevy 3500. The Brophy Clamp On Camper Tie-Downs # HSSF would be the correct camper tie downs for your 2015 Chevy Silverado 3500. These will work on the newer (non-dually) Silverados, as confirmed by Brophy. The # HSSF will need to be used in conjunction with a tie-down hardware package consisting of turnbuckles,...
view full answer...
- Camper Tie Down Recommendation for a 2007 Chevy Silverado 1500 Short BedFor a 2007 Chevy Silverado 1500 Classic or New Body style, provided that the bed is not a step side, is not a double-wall bed, and is not a dually, you can use camper hold downs # HSSF. I also recommend tie down hardware kit # TDHP. I have linked instructions for the hold downs for you. These hold downs are very popular and are the ones I recommend using on your truck.
view full answer... - Camper Tie-Downs for 2013 Ford F150According to CR Brophy, the TDSF is not a fit for your F150. They recommend using the # HSSF, which will work with your truck as long as there is two inches of clearance under the lip of the bedside, as shown in the provided diagram. Full dimensions of the TDSF are available in the thumbnail photos shown on the product page.
view full answer...
- Will Brophy Camper Tie Downs Work on 2020 Chevy Silverado 2500 Long BedYes, the Brophy camper tie downs part # HSSF that you referenced can fit truck bed that have plastic bed rail covers like your 2020 Chevy Silverado 2500. I attached a picture that shows them installed on a bed rail that has the covers like you mentioned. For hardware to attach the tie downs to the camper we have the # TDHP as well.
view full answer...
- Do Brophy Clamp On Camper Tie-Downs Have A Weight CapacityThere is no weight capacity for the Brophy Clamp On Camper Tie-Downs # HSSF. The tie-down hardware kit # TDHP, that is used to secure the camper to the # HSSF tie-downs has a weight capacity of 3,000-lbs. My contact at Brophy said the tie-downs will handle the camper and the concern would be if the truck capacity was not able to handle it, but with an F-350 you should have no issue. Since the front tie-down is behind the camper tie-down, the rear tie-down must be forward of the camper...
view full answer... - Camper Tie-Downs For 2013 GMC Sierra 1500 The BROPHY Camper Tie Down, part # TDSF you referenced is not designed as a fit for your 2013 GMC Sierra but we do have another solution. I recommend part # HSSF. if you have access to the underside of your bed rails. These tie-downs use a clamp-on mounting system that grabs the underside of your bed rails. I have attached a photo that shows how this system is mounted on a truck. I have attached a link to an installation video for these tie-downs you can check out. If you decide on the...
view full answer...
- Truck Bed Camper Tie Down Recommendations for a 2013 Ford F-150The Brophy Camper Tie Downs, part # TDSF can be used on campers that have a total length of up to 8 feet in length. The Brophy Camper Tie Downs, part # HSSF can be used on any size campers. There is no weight capacity rating on the camper tie downs and they will work for any camper size that is properly sized for your 2013 Ford F-150. The Brophy # TDSF mounts into the truck bed stake pocket, where as the Brophy # HSSF tie downs wrap around the bed, not in the stake pockets, and are...
view full answer... - Fit of CR Brophy # HSSF Truck Bed Camper Tie Downs on 2007 Toyota TundraCR Brophy, the manufacturer of the # HSSF tie downs did not test fit on the 2007 Toyota Tundra, so they can neither confirm or deny the fit. I was told that if the bed is single walled and the lip under the bed side is at least 2 inches wide, the tie town should fit (see photo). Torklift offers tie-downs that are a confirmed fit, you can see the different fits available by clicking the provided link.
view full answer...
Do you have a question about this Truck Camper Tie Down?
Used Items Available
Condition: Surface Scratches
Notes: Parts are scratched up, seems to be some signs of instalation, otherwise fine.
Info for this part was:
Expert Research:
Mike L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Brandon M
Expert Research:
Adam R
Expert Research:
Jeffrey L
Expert Research:
Sarah H
Video Edited:
Zack K
Video by:
Patrick B
Installed by:
Matthew K
Installed by:
Cole B
Updated by:
Rachael H
Updated by:
Amanda M
Updated by:
Manda E
Updated by:
Amanda K
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Ed B.
5/22/2020
No problems. Would buy again. Very easy to take on and off the truck.