Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Average Customer Rating: 4.7 out of 5 stars (1557 Customer Reviews)
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.These tiedowns were exactly as advertised and fit my 2023 f350 4wd crew cab perfectly using preexisting holes and mounts. They even came with wire feeders to feed the bolts through the holes on the frame. Instructions were very good and easy to follow. Can adjust the width of tie down and can also drill new holes to customize the width. I highly recommend these.
I bought both the front and rear tie-downs for my old Lance truck camper on a 2023 Ford F-250. Once installed they work great; very heavy duty. But the thing I liked most was the detailed instructions for installation. Everything needed came with the tie-downs and they were perfectly fitted to my F-250. All I needed was my old torque wrench. Installation probably took less than 2 hours.
The package arrived very quickly and intact. I have a 2020 Ford F250 SD Lariat short bed with a factory hitch. The tie-downs were really easy to install although the hitch adapter plate (see attached photo) which is supposed to attach to the end of the tie-down would not fit inside the tubing on my factory installed hitch so I installed without it and it is tight and snug
Someone had used and installed these before so they came to me with lots of scratches and bumps and beat up spots. One of the hitch hooks was actually bent.
Jenny N.
6/14/2024
Oh no! I am sorry that it arrived that way. I can have it replaced it for you and we will be in contact with you.
This is my second set for the TorkLift tie-downs, and I would not use any other type. We use it daily; our camper never comes off as we are constantly on the move. In the event we have to remove it for vehicle service such as alignment, it is easy to remove and get back on.
Torklift makes a top quality product. Installs easily once you understand the instructions. Very solid frame/hitch mount, never have a concern about them flexing or breaking. The second set I've purchased (the first set were sold with the truck they were installed on).
Installed on 2020 F250 Superduty. Easy to install rear tie downs only took about 45 minutes. I love the fact there is no drilling or moving existing things. Just straight bolt on and seem to be rock solid.
The TorkLift Tie Downs are perfect for our truck camper . They make all the differences for making us feel the camper is save and attached as needed. A must have if you are adding a truck camper
Great solid product and easy to install. Solution to your upgrade to a dually for the truck camper.
They have worked great. From Michigan to Alaska and back, no problems! They were easy to install and would recommend them to any truck camper owner.
Super easy to install. I had a bed step mounted and had to remove it to install these, which is kind of a bummer, but not a deal breaker!
Great product easily installed
My rear tie downs took a little longer to get here than the fronts but etrailer has some of the best customer service on the web. Always quick to respond to any inquiry. And shipping speed was excellent too. Etrailer is my go to for all things involving my truck camper.
Installation is about 5 minutes...they install in the sides of the receiver tube.
No problems.
Went together easily, perfect fit.
Have used the manufactures other products and they are excellent products.
Cavers,bryan
1/8/2021
very good,just 1 bolt to remove from RUSTING until needed again
Great fit and easy to install.
Love these. I wish there was some cool end caps to go with them.
The Package arrived on time and all was correct. It was easy to track the order through the shipping process, I found the staff easy to work with and they appeared to be genuinely interested in providing good service.
Rick B.
11/25/2022
Torklift tiedowns are working great, great fit, no problems with install.
Easy install on a 2017 Ford F-350 Lariat w/ factory hitch.
This installation was easy. If installation is on F250, the additional notched plates must be attached to the tie-downs. This prevents rotation inside the receiver tube. A couple of ratchet extensions will be required to hold the bolt head. The finished installation is secure and looks good. The welding appearance could be better, but seems strong enough.
Ronald
4/14/2022
The tie downs are still secure and work great. These rear tie downs will get alot of road grime and mud, so keep them clean.
If you have the factory installed trailer hitch these things take about 10 minutes to install with no modifications necessary. They work great
This system for securing your slide in camper is really good. Instalation is straight forward. Highly recommend.
Great installation was very easy. received front and back tie downs two days ahead of what I was told. Customer service rep was very helpful. A great asset to your company, very knowledgeable.
Very quick and easy.
Fast delivery. Super easy to install.
Do you have a question about this Truck Camper Tie Down?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Heather A.
10/12/2022
Thank you for your photo. Torklift does recommend to use the hitch adapter for the 2020 Ford F-250. The adapter does need to be turn horizontally to fit inside the hitch not vertically.