Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
(218 reviews)
Price: $203.83
In Stock
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
Item # HSSF
Retail:$220.09
Our Price: $203.83
You Save: $16.26
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (218)
- Q & A (0)
- Photos
- Used (1)
Brophy Camper Tie-Downs - HSSF
- Front and Rear Tie-Downs
- Brophy
- Bed-Mounted
- Powder Coated Steel
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.
Features:
- Creates attachment points for securing your camper to your truck bed
- Wide clamps provide superior holding strength
- Turnbuckles (sold separately) required to attach camper to tie-downs
- Protects your truck's paint with neoprene pads attached to the brackets
- Resists corrosion and rust with black powder coated steel
- Clamps securely onto your bed rails - no drilling required
- Includes 4 camper tie-downs with clamp plates, 12 neoprene pads, and installation hardware
- Made in the USA
Specs:
- Application: for exact fits, enter in your vehicle's year/make/model above
- Minimum 2" needed between sidewall and lip of bed rail
- Not compatible with drop-in bed liners, aftermarket bed rails, double-walled beds, or side-step beds
- Dimensions: see diagrams below
- 1-Year limited warranty
No-Drill Installation
These clamp-on tie-downs install quickly and easily, with no drilling or modification to your truck required. Because they're mounted in the bed instead of on the frame or body of your truck, you don't need any kind of fancy mechanical background to get this job done. You just need to slide the hold downs over the rails of your truck and clamp them down with the included T-bars and hex bolts.
The fact that they simply clamp on means that you can remove these tie-downs when you're not hauling your camper, leaving no trace. Use the provided neoprene pads on the T-bolts and tie-downs where they make contact with your truck to make sure no scratches or dents will be left behind either.
It's important that the tie-downs on your truck line up with the anchors on your camper at the correct angle to ensure a secure hold. Ideally the tie-downs should be on the outside of your camper's anchor points, but they can be on the inside as well, just as long as they're not lined up with each other.
Securing your Camper
To secure your camper to your truck, you'll also need a tie-down hardware package consisting of turnbuckles, S-hooks, and chains (TDHP - sold separately). This hardware attaches the anchors on your camper to the tie-downs on your truck to keep your camper safely mounted. Once you tighten the turnbuckles to the correct level of tension (not too tight!), you'll be good to hit the road.
HSSF CR Brophy Truck Camper Tie Downs for Slide In Truck Camper - Camper Hold Down - No Drill Tie Down - 4 Pack
Installation Details
Customer Satisfaction Score:
90% were satisfied with this product
10% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4 - HSSF
Average Customer Rating: 4.6 out of 5 stars (218 Customer Reviews)
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.by: TheAvionNomad01/18/2024
I used these to mount a vintage 1970 Avion C-11 to a 1993 D250. They worked great and were much stronger than I expected - and it was a huge cost savings (and a much more attractive look) than some of the frame mounted options of more than $1000. There were some oddities that I noticed. It was impossible to mount them exactly the way the instructions suggested because of where on the wings near the cab,. The brackets also could not stay on with the camper unloaded because they would hit the jack mounts, meaning they had to me bolted in after the camper was in the truck but before lowering the jacks, making the access to the bolts a frustrating 'feel for it' experience.I'f suggest the manufacturer secure the bolt so that you don't need to hold both sides when tightening/loosening, and also refine it to need less turns to do so. It took me 2 hours to mount the first time, and not much less when removing them with the limited access. The pads also came off in the first use.
I gave it a 5 star because I realize there are limited options for older campers and anything universal is going to have issues with some thing - so that's just my input and experience. Overall pretty reasonable for the price and functionality.
by: Pat03/20/2023
The product was shipped extremely quickly, it arrived 3 days after I ordered them. As far as the product goes I was extremely pleased that they were as easy to install as the product video showed them to be. I had been looking for
a tie down system that would work for my 2018 Ford since I purchased my camper in 2020 and after much research I found these at etrailer. One word of advice is that if your camper has a shower or other design that allows the camper to extend across the bed behind the wheel wells, either move the rear tie downs forward or shorten the leveling stud before you attempt to load your camper. On mine it turned out that once the tie downs were placed and attached I had to cut off about 3 inches of the threads.
Other than that it was an easy install although the bolts that attach the tie downs to the under lip clamp are a challenge to install but take your time and they will go on. I will post an update once I have been on the road for a few trip and see how they are working.
Thank you etrailer for your super fast shipping and online product videos.
by: Ed B.05/21/2019
Purchased the Brophy camper tie down set of four for the Palomino truck camper I just purchased. These are my second set as the first set were sold with my Hallmark camper. Easy to install and hold the camper in the truck with no worries.
by: James 05/20/2024
Ordered these for new camper. Very easy to install and does the job without the high cost of frame mount.
by: Jeff Smith10/22/2023
These tie downs work great. It holds my 3k lb Cabover camper in place without issues. And I live in my camper, so not losing my home is very important to me!!
by: Shelly12/13/2023
The products arrived on the time scale as stated. The packaging did not hold up and the box with the metal tie downs was broken open. There was too much weight for the box and it just split open. Not sure if anything is missing. Packaging of items that are heavy should be more secure and sturdy.
Jenny N.
12/14/2023
Oh no! I will have our Customer Service team reach out to you. If anything is missing we can take care of it.
by: Allen.08/22/2022
These wont work for my truck and camper. The box on a 2018 gmc 2500 short bed does not lend well to placement of these in order to get the correct geometry i needed for the tie-down points on my Palomino maverick 6601. I had high hopews of not having to buy the frame mounts, but i will have to.
Mike L.
8/31/2022
The HSSF tie downs have specific fit parameters as mentioned in the product specifications above: External bed rail width cannot exceed 5-12 Requires at least 2 of space beneath lip of bed rail Not compatible with -in bed liners, bed rails, double-walled beds, or side-step beds
Allen.
8/23/2023
In response to the etrailer comment response, they fit on the bed fine, with plenty of clearance and would work for a smaller camper. they just did not fit in the right spots for my truckcamper combo.
by: Ron W07/02/2016
As far as I'm concerned these are junk. Wasted my money. Do not mount in proper location on a 2011 Chevy Silverado 6.5' Bed. Because of the design of the bed rail the mounts cannot be installed in the proper locations for securing camper. The photos show the maximum forward and back that these can be mounted. Not at all made for the 6.5 foot bed 2007 or later Siverado. The Black Powder Coated Steel isn't that great either. Paint missing, dinged up from storage and shipping probably.
by: . George01/03/2024
The tie downs are great no problems.Very easy to install.I keep them on my truck all year long Thank you
by: Terry08/08/2023
Order arrived quickly, priced ok. Box was broken open by shipper NS the 4 T-bolsts bolts ere missing. Etrailer shipped ou the missing parts a few days later, but in the meantime I fashioned t-bolts I could use for my trip. Many customer comments on this camper Brophy tie-down match my experience. Etrailer follow up was great, but surely must be aware that their packing is sub-standard. Perhaps zip-tying the T-bolts to larger pieces would eliminate the loss even in case of breakage. Functionally the tie-dows were easy to install and seem quite adequate for off-road use of my in-bed camper. Will continue to use etrailer because of their excellent customer service.
by: captkirk02/15/2021
These tie-downs worked awesome for our pop up camper on our 1998 F150. Super snug, haven't loosened up or moved on the truck, camper hasn't budged either. I was leary at first not having the camper tied to the frame but now I have total faith in these tie downs.
by: Mike S05/23/2020
These Brophy tie downs have worked great over the past year. I leave the camper on the truck and it is my daily driver as well as RV. The camper weighs in at 1500 dry and about 2000 loaded. I do not do any radical 4x4 but I have taken some backwoods off road logging trails.
by: Bing09/23/2019
I received this tie downs on July, and first used it yesterday.
My Camper ‘s dry weight is about 1600 lb, and the products are good for my truck camper.
The problem was the position where tie downs were fitted on my truck. I tried several times to fitted tie downs to my truck.
by: Brent 08/08/2019
I bought these for our brand new 2019 GMC Sierra 1/2 ton because no custom options were available. I was happy that they were easy to install, and look great. I’ve used them in the past and have been happy with how they hold campers. Sure I’d rather have custom mounts from the frame, but for the price and because these are my only option that’s what I got. These will work just fine, and I like that I can swap these out on trucks.
The one thing I wish was different was that the threaded T handle portion would have a longer option. I had to fancy up a 2”x6” to run inside the side of my p/u bed so they would touch something.
As always another great shopping experience with etrailer. They haven’t let me down yet. Especially Lori, what a great customer service rep.
by: Patrick04/02/2020
These things are solid although i put duck tape on the T pads....installed 2014 Chevy Silverado 6.5 ft bed for 1200lb Starcraft.
Patrick
4/6/2021
Still have not moved! Great design and cost savings.
by: Matt04/14/2015
These camper hold-downs appear to be manufactured from good steel stock and should do the job nicely. I did have one piece that was slightly damaged but was not caught when packaged (the damage was not due to shipping). I was able to take a hammer to the bent steel and straighten it sufficiently to use the part. It was a little disappointing however, and should have been caught prior to shipping.
Overall I am pleased with the quality and price
by: Regan06/25/2019
Using on 2013 Ford F150 for a smaller cabover. Great quality product, shipped fast, works great. Had to turn bolts around to clear inside of bed. Held camper solidly over rough trails!
by: Bryce05/10/2022
Fits well on a First Gen Tundra. I was extremely unsure about fitment for my truck but they work great! Install only takes 5-10 minutes. I would definitely recommend. Steel is quite thick and seems very strong.
by: John05/25/2020
Easy to install and have done what’s expected. Keep the camper in place!!
by: JAMES K09/24/2012
ORDER ON TUESDAY RECIEVED ON FRIDAY NOON SAME WEEK ONLY PROBLEM WAS 4 7/ 16 NUT WERE 4 1/2 NUT HAD TO BUY 4 NUTS OTHER THEN THAT I WOULD BUY OFF ETRAILER AGAIN VERY GOOD SERVICE
by: Chuck11/13/2012
Found easy to install, I placed lock washers on the 8 3/8" bolts. Sold at Menards for 89 cents (pkg of 8) not in kit. Placement was a little restrictive with dealer installed bed liner. Takes 30 minutes to install all 4. Great buy.
by: Neil08/04/2021
Arrived on a rainy day with the box falling apart. Too much heavy steel to be loosely packed. Fortunately, the hardware bag was still there. Some bare metal showing. I had some emails with MacKenzie B. and they were responsive and without asking they offered me a 5% refund for the damage. After my first trip, they performed well on some very bumpy roads. Held strong and didn't move. I did have to re-adjust the lower standoffs after the first week. Taking them on/off is frustrating because the 2 nuts are in the small gap behind the clamp against the inner bed wall. Too tight for all but an open end wrench. 1/6 turn times too many fumbling tries, arg! Also, I was nervous not having a locking feature (lock washer, locknut, etc). I bought 8 locknuts (pinch type) and welded them to the inner plate. Then bought 8 round head hex bolts (grade 8). So now I can install easily with an Allen socket. See pictures. Recommend eTrailer consider this modification.
Neil
8/5/2022
After my mount bolt mod, Ive used these multiple times and they are working great! Very stout and no visible marks on my F250 bed.
by: Jason S.06/05/2019
These tie downs were a great budget solution in leu of a permanent installation of my camper shell and/or frame mounted tie downs. Aside from needing to plan their placement (they can hang in front of the gas cap if you don't plan it right the first time around... no, I didn't accidentally block my gas cap... maybe I did) and take into consideration they also need a little bit of internal clearance as well, they work just fine. I haven't noticed any cargo shifting nor warping of the truck bed around where they are installed. My camper shell is under 1K lbs and it holds just fine.
Jason S.
6/8/2020
A year later & they still hold strong.
by: Dayton12/15/2023
Awesome customer service my new fav pl ace
by: dave07/08/2016
Its a good product for a light camper. I personally would not use it on anything heavier than 1000lbs. But then iam not an engineer. I sold mine and my camper and bought frame mounted tie downs
Dave
7/11/2017
Did not work for me. Tried to send them back but shipping would cost a bundle so i would get less than half of what i paid. Sold them same day on-line. Not good for a larger camper.
Rachael H.
7/12/2017
25
218
Show More Reviews
See what our Experts say about this Brophy Camper Tie-Downs
- Will the Brophy Camper Tie Downs # HSSF Fit a 2004 Dodge Ram 2500 Four Wheel DriveThese Brophy Camper Hold Down Brackets, # HSSF are considered a universal-fit item that will work on most full-sized trucks, including your 2004 Dodge Ram 2500 4 by 4. Please note that some Dual rear wheel truck beds may interfere with the installation of the hold downs. The Brophy Brackets # HSSF install by wrapping around the bed rail, instead of using the bed stake pockets. Included with the brackets is the hardware for fastening the bracket to the truck. If you do not already have...
view full answer... - Brophy Camper Tie Downs that Fit 2012 Ford F-250Yes, the Brophy camper tie downs part # HSSF that you referenced are a fit for your 2012 Ford F-250 and will work well. You'll also want the hardware kit part # TDHP to secure the tie downs to your camper.
view full answer... - Frame Mounted Camper Tie Downs that Fit 2021 GMC Sierra 3500The Brophy T-Bolt Replacements part # BR2007 that you referenced are 6 inches long and would be same size as what came with your # HSSF. The best option we would be the Torklift frame tie downs part numbers # TL44FR and # TLC3221 for if you have a single rear wheel setup or the part numbers # TL44FR and # TL84FR for if you have a dually setup.
view full answer... - Will Camper Hold Downs Fit On The 1995 GMC Sierra 1500 4 x 4 with a 8 Foot CamperYes, the Camper Hold Downs, part number HSSF will work on the 1995 GMC Sierra Pickup. The hold downs do not fit in the stake pockets but wrap around the bed rails and are mounted inside the bed. When attached the chains are tightened and pressure is applied from the inside of the bed out and down.
view full answer... - Does the Brophy Clamp # HSSF Fit A 2018 F150 Crewcab 5.5 BedYes, the Brophy Clamp On Camper Tie-Downs # HSSF will work just fine with your 2018 Ford F-150. The Brophy Tie-Downs are easy to install and remove and require no drilling for installation. The Brophy Tie Down # HSBP will work for you if you have the required 5.5 inches of maximum width and have the 2 inches of space under the bed rail. In order to secure the truck bed camper to these tie-downs you will also need the Brophy Basic Turnbuckles # TDHP. If you have any further questions please...
view full answer... - Will Brophy HSSF Tie Downs Fit 2004 Chevy Silverado 2500Brophy has told us before that their tie downs # HSSF are a fit for the 2004 Chevy Silverado so this kit would fit and work well. For the hardware kit to secure your camper to the tie downs you'd then want the part # TDHP.
view full answer... - Camper Tie Down Recommendation for 2012 Nissan TitanBrophy tie downs, # HSSF, will work well for you. This setup is rated for use with any camper that fits the bed dimensions of your truck so it would work well with yours. We do not carry the donuts you mentioned that usually go around the center window of the rear window.
view full answer... - Camper Tie Down Recommendation for a 2014 Ram 1500 with Running BoardsI have a set of camper tie downs that will fit your 2014 Ram 1500, but they attach at the stake pockets of the bed and not the frame like the Torklifts do. There is no Torklift option for your truck if it has running boards. The Brophy Camper Tie Down, part # HSSF is a universal fit item and will work on your 2014 Dodge Ram 1500. The Brophy Tie Down mounts over the sidewall of the truck bed. The recommended hardware kit to install part # HSSF is Camper Tie Down Hardware Package, part...
view full answer... - Recommended Camper Tie Downs for a 2015 Chevrolet Silverado 1500 Out of all the Brophy Camper Tie Downs we carry, I recommend the Brophy Clamp On Camper Tie Downs # HSSF. I recommend these tie downs as they can fit beds with spray in liners and are the most popular Brophy Tie Downs we offer. To make sure these tie downs will fit your truck bed you will need to take a few measurements. The width of your bedrail cannot be larger than 5-1/2" and you need at least 2" of space beneath the lip of the bed rail. You also cannot have plastic bed rails, double-walled...
view full answer... - Camper and Tie-Down Recommendation for Ford F250 Super Duty with 6-1/2 Ft BedI spoke with one of our local RV dealers here in Saint Louis and he said that they offer a 6.8 and 8.6 Ft truck camper that would work with your truck. You will need to drop or completely remove your tailgate before hauling this type of camper. When choosing a camper you will also want to make sure that you do not exceed the weight capacity of your truck. When it comes to tie-downs, I personally recommend going with our custom fit TorkLift camper tie-downs like the # TLF2012 and # TLF3006....
view full answer... - Tie Downs for my 2006 GMC Sierra Extended Cab and Palamino In-Bed CamperAs long as the bed in your 2006 GMC Sierra is not a step-side, double wall or a dually, then the Camper Hold Downs, # HSSF, will work well for you. Take a look at the helpful link I have included to see how these tie downs install. These tie-downs wrap around the bed and do not fit in the stake pockets. Stake pocket mounted tie downs that will fit your truck are not available. With these tie-downs, I recommend the camper tie down hardware package, # TDHP.
view full answer... - Camper Tie Down Recommendation for a 1998 Dodge Ram 3500The portion of the Camper Tie Down part # TDSF that inserts into the stake pocket of the truck measures 1-7/8 inches wide by 1-5/8 inches deep. Based on the dimensions you listed they wouldn't fit as they would be 1/8 of an inch too deep. A better option would then be the Camper Hold Downs, # HSSF. I attached a picture that shows how these will look when installed. You will also need the hardware kit part # TDHP. You should only need 4 of these to secure your camper. These are only sold...
view full answer...
- Can Zinc Plated Brophy Tie-Downs be Used with Aluminum Bed on Ford PickupYou can use the Brophy Clamp On Camper Tie-Downs # HSBP with the aluminum bed on your Ford pickup but you would want to remove them frequently. If you are planning on keeping them installed for a long period of time then you will want to go with part # HSSF instead which is the exact same tie-down just with a black powder coat finish. The zinc plating on the steel will react with the aluminum a lot quicker than the black powder coat will wear off of the other tie-downs. If you will be...
view full answer...
- 2004 Ford F150 FX4 6.5 ft bed Camper Tie Down RecommendationWe don't have a lot of specific fit information for the Brophy Tie-Downs part # HSSF that you referenced, but we do know that they can't be installed on a 2004-2008 Ford F-150. The best option I can make for you would be the # TDSF that installs in the stake pockets. You will also want the hardware kit part # TDHP.
view full answer... - Truck Bed Camper Tie-Downs for 2013 Chevrolet SilveradoI haven't heard of a specific issue like that with the 2013 Chevrolet Silverado. But there is truth that stake pocket tie-downs are not as secure as clamp on tie-downs. There's a lot pulling on the tie-downs and with the stake pocket design there's a lot of movement and chance of damage to the truck. We have a couple options by Brophy, # HSSF and # HSAB. Both are better than a stake pocket tie-down.
view full answer... - Correct Brophy Clamp On Camper Tie-Downs for a 2009 Ford F-150The Brophy Clamp On Camper Tie-Downs part # HSSF will fit a 2009 Ford F-150 and they can be used with the Brophy Basic Turnbuckles part # TDHP. The combination of these two parts will give you everything needed to secure a truck bed camper.
view full answer... - Can Brophy Camper Tie Down # HSSF be Used with Camper that is Longer than 8 FeetYou are correct the versions of the Brophy camper tie downs that attach to the truck bed rail pockets are limited to 8 foot long campers but the clamp on style like part # HSSF can be used with longer campers like what you have and will work great with your 2003 Chevy Silverado 2500HD.
view full answer... - Camper Tie Downs for 2015 GMC Sierra Short Bed that Attach to Bed RailsFor a set of camper tie downs that attach to the bed of your 2015 GMC Sierra 1500 I recommend the # HSSF. These tie-downs use a clamp-on mounting system that grabs the underside of your bed rails. I have attached a photo that shows how this system is mounted on a truck. I have attached a link to an installation video for these tie-downs you can check out. If you decide on the # HSSF tie-downs you will need the Camper Tie Down Hardware Package, part # TDHP. This package includes the turn...
view full answer...
- Brophy Camper Tie Downs that Fit 2016 Ford F-150 Short BedAccording to my contact at CR Brophy Machine Works, their # HSSF truck bed camper tie-downs are compatible with the 2016 Ford F150. You'd also need the hardware package, part # TDHP, which includes the hooks, turnbuckles and lengths of chain to connect the tie downs to the camper. The # HSAB will not fit your truck.
view full answer... - Will Brophy Camper Hold Downs # HSSF Fit a 2009 Chevy Silverado 1500 and North Star Pop-Up CamperAs long as your 2009 Chevy Silverado does not have a step side bed, double wall bed, and is not a dually then the Brophy tie downs, # HSSF, would be an excellent choice for you. The tie downs are going to work with any camper that is the proper size for your truck. I recommend adding the tie down hardware package # TDHP to help secure the camper to the tie downs.
view full answer... - In-bed Camper Tie Down Recommendations for a 2009 Dodge Ram 1500The Extang CargoCleats Truck Bed Tie-Down Anchors - Clamp On - 500 lbs - Qty 2 # EX1932, have a weight capacity of 500 lbs each. You will have to also make sure that the straps that you use also have enough strengths for the application. The tie-downs fit underneath the bed rails like in the video I have linked for you. Provided there is nothing in the way they could fit your 2009 Dodge Ram 1500, they are a universal fit, but will not work if you have the OEM bed rail cap installed. Since...
view full answer... - Will Brophy Camper Hold Downs # HSSF Fit a 2009 Dodge Ram 1500 With a Bed LinerThe Brophy Camper Hold Downs, part # HSSF, will fit trucks with spray-in bed liners, but if it has a slide-in bed liner the bed liner will have to be trimmed away in the shape of the hold downs. The installation does not involve any drilling or modification to the truck bed. It is installed by tightening two bolts on each clamp. I am including a link to the installation instructions for the hold downs. You may also be interested in the Camper Tie Down Hardware Package, part # TDHP.
view full answer...
- Camper Tie-Down For Bronco 800 Camper On 2003 Toyota Tundra PickupThe Brophy Camper Hold Down, part # HSSF slips over the bed rail of your 2003 Toyota tundra, and with the provided hardware creates a tie-down for your Bronco 800 camper. You would also need the Brophy Tie Down Hardware Package, part # TDHP, which includes hooks, chain and turnbuckles. The tie down hardware will attach to existing eye bolts built into the underside of camper. If your camper does not have such an attachment point, you can add them, as long as they attach to the frame...
view full answer...
- Can the Brophy Clamp On Camper Tie-Downs Be Used On a Ford F-150 with Aluminum BedWe have spoken with Brophy in the past and for a Ford F-150 with aluminum body such as your 2017 model they recommend using the Brophy Clamp On Camper Tie-Downs part # HSSF. There won't be any issues with these tie downs and an aluminum bed so long as you are not exceeding other figures such as payload capacity etc. In order to secure the truck bed camper to these tie-downs you will also need the Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs part # TDHP. Although certainly...
view full answer...
Do you have a question about this Camper Tie-Down?
Used Items Available
Condition: Surface Scratches
Notes: Parts are scratched up, seems to be some signs of instalation, otherwise fine.
Info for this part was:
Expert Research:
Mike L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Brandon M
Expert Research:
Adam R
Expert Research:
Jeffrey L
Expert Research:
Sarah H
Video Edited:
Zack K
Video by:
Patrick B
Installed by:
Matthew K
Installed by:
Cole B
Updated by:
Rachael H
Updated by:
Amanda M
Updated by:
Manda E
Updated by:
Amanda K
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Ed B.
5/22/2020
No problems. Would buy again. Very easy to take on and off the truck.