Will Camper Hold Downs Fit On The 1995 GMC Sierra 1500 4 x 4 with a 8 Foot Camper

Question

Question:

would like to know if these will work on my 95 GMC sierra 1500 4x4 with a 8 camper thanks

asked by: john K

0

Expert Reply:

Yes, the Camper Hold Downs, part number HSSF will work on the 1995 GMC Sierra Pickup. The hold downs do not fit in the stake pockets but wrap around the bed rails and are mounted inside the bed. When attached the chains are tightened and pressure is applied from the inside of the bed out and down.

expert reply by: Robert G

0

Answer 1

CR Brophy, the manufacturer of the #HSSF tie downs did not test fit on the 2006 Toyota Tundra, so they can neither confirm or deny the fit. I was told that if the bed is single walled and the lip under the bed side is at least 2 inches wide, the tie…

view full answer...

Answer 2

I reached out to Brophy to check into this for you. The Brophy Clamp On Camper Tie-Downs #HSWB are tested on domestic, full size bed trucks only so while these have worked on Toyota Tundras before, the double cab may be a challenge here. The tie…

view full answer...

Answer 3

The Brophy Camper Tie Downs, #TDSF, are a universal fit kit intended to fit as many trucks as possible. But there is no fit guide available stating which trucks are compatible. It is still very likely that they will fit your 2011 truck but it's…

view full answer...

Answer 4

CR Brophy, the manufacturer of the #HSSF tie downs did not test fit on the 2007 Toyota Tundra, so they can neither confirm or deny the fit. I was told that if the bed is single walled and the lip under the bed side is at least 2 inches wide, the tie…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Will Camper Hold Downs Fit On The 1995 GMC Sierra 1500 4 x 4 with a 8 Foot Camper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching