Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
This round vent forms the interior part of the Alliance 2-piece enclosed trailer vent. Constructed of UV-resistant polypropylene plastic that holds up to sun exposure. Black color.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Jake: Hey guys, it's Jake here with etrailer. Today we're going to be taking a look at the Redline half-moon trailer vent. This is going to allow fresh air to get in and hot air to get out without having to worry about getting any water inside your trailer.In this kit, you are going to get the outside vent and the inside receiver so that you can have a nice clean look on the inside of your trailer. This is really going to be important for if you have a wall inside your trailer like we do, but if you don't have a wall, you can just use this part and you'll be able to mount it to the outside of your trailer and get fresh air without having to worry about any water.So you can buy these as a kit or you can buy them separately. Now here you'll see we have our vent in black. It's also available in white if you'd like to match it to your white trailer.Here's that piece on the inside wall that we we're talking about.
This is going to give it a nice clean look so you just don't have an open hole in your wall. It's going to have a nice flush mount design so you don't have to worry about anything running into it when it's on the wall. It's also going to help preserve this part from being damaged.If you want more of a cross-flow to go into your trailer, you could pick up a couple of these vents to be able to put one on the opposite corner of your trailer so that you have wind coming in the front and going out the back. When using two vents, it's going to provide a way for cool air to get in and warm air to get out. Now that we've gone over some of those features, let's go ahead and show you how we got it installed.We'll start by drilling a 3" hole.
We're going to start on the inside so that we know we're not going to run into anything inside the walls. You can see we have our ribs here and here, so we're going to split the difference and do it in the middle of them. Then we're going to continue with the hole saw through the sheet metal on the outside so we know where our hole needs to be drilled. We'll go ahead and insert our pilot bit into the hole that we punctured through the sheet metal and start drilling out our hole.I'm going to go ahead and insert our vent on the inside and fasten it down. Here we just found some stainless steel screws so we don't have to worry about any rust.
Now we can move to the outside, and we can go ahead and get our outside vent in place, slide it over. We'll use a self-tapping screw, but you want to be careful with this sheet metal on the outside of your trailer. It's not very thick. You don't want to strip it out. We'll stop right there and hand-tighten from here.
Now we'll go ahead and get the other five screws in place.Now, we went ahead and put some of this Loctite black silicon gasket on the inside. We took our cover off and put it on the inside to seal it up nice and neat to make it a nice watertight seal. We do have this at etrailer. You can pick some up if you'd like.Once you have all your screws in place, you're ready to hit the road.With all that being said, that's going to do it for our look and installation of the Redline half-moon trailer vent.
Average Customer Rating: 4.9 out of 5 stars (31 Customer Reviews)
This round vent forms the interior part of the Alliance 2-piece enclosed trailer vent. Constructed of UV-resistant polypropylene plastic that holds up to sun exposure. Black color.Perfect for venting the small cargo trailer I have. Only purchased this part, as I had found the others locally but was missing one. So if you're buying, don't forget to purchase the outside one :)
Great service and delivery time. Thank you!
I purchased these register covers to install as the interior grills for dorade vents on a 44 foot sailboat. I glued fine mesh screens to the interior tubes to prevent the ingress of noseeums and other insects. Very good value for my purposes and look very finished. Two thumbs up.
Great service!!!!!!!!!!!!!!!!!!!!!
Product was EXACTLY what I needed. Placed an order right after for a new trailer hitch!
Installed this simple yet perfect 3” vent cover for a bathroom exhaust fan.
Just what I wanted and works very well to help keep condensation out of my trailer.
Perfect!
Just what I’ve been looking for.
High quality product just as described.
Ingrid
7/23/2021
These vent covers have held up nicely. Really good quality product.
Item was exactly as described, works perfectly for our application (vents in an animal cage) and shipping was fast. Thanks!
was easy to install and works great
Arnie A.
9/28/2018
good so far
Great product and easy to install
Edward W.
5/29/2021
Product is still holding strong.
EASY TO INSTALL NICE PRODUCT.
Brad S.
8/23/2021
GREAT!!
Hasn’t cracked or leaked in a year. Thumbs up!
we have no complaints about this product.
Good product great price and no ripoff on shipping
was what i expected
On time and working fine
Super fast shipping, product as describ ed
exactly as described on-line
Using them as vents on the house, great product and fast delivery.
Just what I needed
Quality!
Outstanding customer service.
Great product and fast shipping !
Great!
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Faye
5/31/2019
Great to allow heat escape and air flow. Customer service is amazing!