Rear View Safety Splice Kit

See what our Experts say about this Rear View Safety Accessories and Parts

• Can You Use Mito Corporation Cameras with the Rear View Safety 9" Color Monitor
  I contacted the manufacturer in regards to your question, they informed me that the Rear View Safety Color Monitor # RVS-6139Q uses cameras with 5 pin connectors, so your Mito cameras with 6-pins would not work unless you wanted to use the Rear View Safety Splice Kit # RVS-SPK01 to splice your cameras in. They did strongly recommend that their cameras, like the Rear View Safety Backup Camera # RVS-771, Rear View Safety Side Camera - Driver's Side # RVS-775L and Rear View Safety Side Camera...
  view full answer...
• Can The RVS Color Monitor Be Used With Voyager RV Side Cameras?
  I went ahead and contacted Voyager about this, and they told me that the Voyager RV Side Camera is only designed to work with Voyager monitors like the Replacement Voyager WiSight 2.0 Wireless RV Backup Camera Monitor # ASA27FR. This is because these cameras use a proprietary connection that only Voyager monitors use. With that being said, even using the Rear View Safety Splice Kit # RVS-SPK01 won't allow you to be able to use the Voyager camera with the Rear View Safety Color Monitor...
  view full answer...
• Wired RV Backup Camera System to Replace OEM Setup on 2004 Winnebago Itasca
  I reviewed Winnebago documentation for 2004 model year motorhomes and some came with the option of a Jensen in-dash radio/rearview monitor system while others did have a Sony option. The best way to know what was installed on your specific RV is to check with Winnebago using the RV's individual VIN. I also checked forums and found comments from owners saying that the Sony system has been made obsolete and is unable to match up to new components, making a complete new camera system the better...
  view full answer...
  
• Rear View Safety 5-Pin Connector Splice Kit Contents
  The Rear View Safety Splice Kit # RVS-SPK01 contains 2 female connectors. If you are needing one male and one female connector I recommend using the Rear View Safety Camera Extension Cable # RVS-101N and cutting it so that you have one female and one male connector.
  view full answer...
• Is It A Good Idea To Solder RVS Camera Splice Kit
  For the Rear View Safety Splice Kit # RVS-SPK01 I think that is a great idea, soldering them together and protecting them with heat shrink will guarantee they are connected properly while protecting the connection from damage. To accomplish this, if you do not already have the tools you need, you can use a soldering iron like the Cordless Soldering Iron # PTW2000 and a solder spool like Solder Spool # FL0803490.
  view full answer...
• Recommended Camera System Upgrade Using Existing Sony Wiring on 1991 Holiday Rambler Imperial
  The easiest way to tell if you need to upgrade your wiring is to disconnect your monitor and camera to check the connection points. You may be able to use your current wiring if you use an adapter like the Rear View Safety Splice Kit # RVS-SPK01. It is highly likely you have a 4 wire system and will not utilize the audio feature. I've attached a photo to assist. If you just want a replacement camera, then I recommend the Rear View Safety Backup Camera - 150-Degree Viewing Angle - 8...
  view full answer...
  
• Replacement 5-Pin Female for RVS Camera System
  To replace the female 5-pin connector for your RVS backup camera system we have the Rear View Safety Splice Kit # RVS-SPK01. This comes with 2 of the female connectors that have bare wires on the other end so you can cut off your current connector and splice in the replacement.
  view full answer...
• Is The Rear View Safety Color Monitor Compatible With The Factory Camera On A 2016 Jayco Precept?
  Without knowing which cameras you have installed on your 2016 Jayco Precept, I can not say for sure if they will be compatible with the Rear View Safety Color Monitor # RVS-6139Q. However, if your cameras are not compatible, you can use the Rear View Safety Splice Kit # RVS-SPK01 to make them compatible with this monitor.
  view full answer...
• Backup Camera Compatibility with 5th Wheel Tailgate
  For a 5th Wheel Tailgate like # VGD-10-4000, I recommend the Rear View Safety Backup Camera System with Flush Mount Camera # RVS-7707721 or the Rear View Safety Backup Camera System - Mirror with Monitor # RVS-772718 with this same camera. This is one of the more rare flush mounted cameras that will allow you to run the wires through the tailgate to give you a really clean look. You can mount the camera inside the composite tailgate or attach it to the outside. The outside lens diameter...
  view full answer...
• Troubleshooting Work Around for 5th Wheel Louvered Tailgate with Camera and Sensors
  A very valid question. There used to be one with an integrated camera and the manufacturer discontinued them. Your best option is to do some engineering yourself to integrate those options. I recommend the Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate with Lock for Ford Trucks # VG-15-4000. Then you can use the Hopkins Smart Hitch Backup Camera and Hitch Aligner System # HM50002 for a separate system at your license plate. If you want to integrate the camera into the...
  view full answer...
• Recommended Trailer Connector for 3 Camera Trailer Connection and Ford Monitor with RCA Inputs
  For your desired connection, I recommend the Rear View Safety Trailer Tow Quick Connect/Disconnect Kit - 3 Camera Set Up # RVS-2133 then use the Rear View Safety Multiplexer Box - 3 Channel # RVS-501N. This will give you the video output and the female RCA connections. If you need the RCA male you can use # RVS-RCA5-AM. You will need the Rear View Safety Splice Kit # RVS-SPK01 to convert from 4 pin to 5.
  view full answer...
• Rear View Safety Monitor Compatibility with Velvac Cameras Already Factory Installed
  The Rear View Safety Color Monitor - 9" LCD Digital Screen # RVS-6139N is not directly compatible with the Velvac mirror cameras. However, when you use the Rear View Safety Splice Kit # RVS-SPK01 they can be compatible according to my tech contact at RVS. This would give you the monitor view you desire utilizing your current cameras. The 4 pin to 5 pin conversion should be easy.
  view full answer...
• Observation System Recommendation to Replace Sony Setup
  The best solution we'd have would be an all new observation system since we don't have a way to adapt your Sony backup camera to your trailer. The Furrion kit part # FOS43TASF will give you a wireless camera that will mount on your trailer that has really great reception and also a monitor that mounts on the interior of your vehicle. Since the camera is wireless all you need is an activation circuit from the trailer's wiring to trigger it. Typically this is the running light circuit. This...
  view full answer...

Do you have a question about this Accessories and Part?