#84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter

See what our Experts say about this TruRyde Trailer Spindles

• What Size Spindle do Bearings L68149 and L44649 fit on
  Yes, you are going to want a spindle that has the 1.063" and 1.378" measurements. This is commonly known as a #84 spindle and can be found on our site with a few variances. For example, the TruRyde EZ Lube Spindle # TRU74FR comes with a brake mounting flange and a grease zerk fitting while the Redline Spindle # TRU64FR does not come with the flange or a zerk fitting. These fit the typical round applications but we also have one for a square application with part # TRU47FR. Any of these...
  view full answer...
• Do You Have a Replacement Wheel Hub For a Discontinued Harbor Freight Boat Trailer?
  Unfortunately Tim, I have no way to know for sure what size spindle you have on your discontinued Harbor Freight boat trailer. If you can provide me with the measurements off your spindle as seen in the image below I can see if we have a hub which will fit but as is most common with Harbor Freight trailers I have seen you are most likely going to need 2 new Spindles # TRU64FR and Hubs # AKIHUB-545-35-G-EZ-K.
  view full answer...
• What Size are the Bearings in the Titan Disc Brake Kit # T4747200 and the Spindles That They Fit
  The bearings that are included in the Titan Disc Brake Kit, part # T4747200, are the # L44649 for the outer bearing and the # L68149 for the inner bearing. The # L44649 outer bearing has an inside diameter of 1.063, which is 1-1/16 inches and the # L68149 inner bearing has an inside diameter of 1.378, which is 1-3/8 inches. These dimensions match the dimensions on your spindle. The Titan Disc Brake kit will work on tandem axle trailers with 3,500-lb axles and a wheel size of 14 inch or...
  view full answer...
• Spindles for a Trailer Hub Assembly for 3500 lb Axle
  The following spindles will fit hub 84545BX 1. Square #84 Spindle for 3,500-lb Trailer Axles - 1-1/2" Wide (8-1/4" OAL) # TRU47FR 2. #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter (8-1/4" OAL) # TRU64FR 3. #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter (11-1/4" OAL) # TRU84FR
  view full answer...
• Spindle and Hub that Fits Dexter Hub 8-248
  We have the Dexter hub part # Q-HUB84545 that you are looking for. Then for the correct spindle that fits this hub you'd want the part # TRU64FR.
  view full answer...
• How to Choose Correct Replacement Trailer Spindle
  Definitely feel free to send in a photo of the damaged spindle, but photos can only help out so much. The best way to know we're getting you the correct spindle replacement is for you to measure the spots along the spindle where the bearings and seal are seated, as well as note the weight capacity of your trailer axle. Once we know all of this we can filter through our selection and find the best replacement option for you. For example, the #84 spindle # TRU64FR uses inner bearing # L68149,...
  view full answer...
  
• What Spindle Will Work for Trailer Hub Assembly with L68149 Inner and L44649 Outer Bearings
  The Trailer Hub Assembly # 84550BX that you referenced will use # L68149 as the inner bearing and # L44649 as the outer bearing. These are the inner and outer bearings used by a # 84 spindle. We offer the following spindles: #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter (11-1/4" OAL) # TRU84FR [R2061-284] #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter (9" OAL) # TRU74FR [R20384EZ] #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter (8-1/4"...
  view full answer...
• Spindle Replacement Recommendation For Donahue Horse Trailer
  In order to make sure you get the right components for your Donahue Horse Trailer, we will need some more information. If you are wanting to replace the spindle, the first thing you will need to know is the weight capacity and dimensions of the axle you plan on using the spindle on. Please keep in mind that installing the spindle require welding it to the axle by a certified welder. They use special jigs so that it is concentric and square on the axle or it can cause problems with uneven...
  view full answer...
• Which Trailer Spindles Fit Trailer Hub Assembly # 84555UC1
  I have three options that will fit Trailer Hub Assembly # 84555UC1, for 3,500 lbs. Part # TRU64FR is a standard 1-3/4-inch round spindle that measures 8-1/4" in overall length. Part # TRU84FR is a standard 1-3/4-inch round spindle that measures 11-1/4" in overall length. Part # TRU74FR is an EZ lube 1-3/4-inch round spindle with a grease zerk that allows you to pump grease internally into the spindle. It also contains a brake mounting flange. It measures 9" in overall length. Installing...
  view full answer...
• Upgrading 8" Hydraulic Brakes to Disc That Will Fit a 10" Wheel and Tire
  The Kodiak Disc Brake Kit # K2HR35D-8 is designed to fit a #84 Spindle # TRU64FR that is typically found on 3,500lb axles. This kit use 8" rotors allowing you to fit a Kenda 205/65-10 Bias Trailer Tire with 10" Galvanized Wheel # AM3H490. You will need either the EZ Lube # DBRKHW35EZ or Standard # DBRKHW35 Bearing Kit to mount the included hubs on your spindle. You will also need to upgrade your surge coupler from drum to Disc # DM62VR. If you can tell me exactly what coupler you have...
  view full answer...
  
• Trailer Hub To Spindle Combinations for 2000 Pound or 3500 Pound Axle
  The HUB KIT # 8-259-5UC1, uses a 1,000 pound spindle, item # TRU44FR. This setup is for a 2,000 pound axle. The #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter, item # TRU64FR, is for a 3500 pound axle. If you need a hub and spindle for a 3,500 pound axle then you would use the # TRU64FR spindle and the Trailer Hub Assembly for 3,500 lbs Axles with 5 on 4-1/2 bolt pattern, item # 84545BX.
  view full answer...
• Recommended Trailer Idler Hub for a Trailer with 84 Spindles
  The threaded portion of the spindle isn't that important when picking out a replacement hub. That portion of the spindle is only for the castle nut, and since you have that already you would be fine. As long as the rest of the dimensions of your spindle match the # TRU64FR then the hub part # 84545BX would fit.
  view full answer...
  
• What Information is Needed to Add Brakes to a Trailer
  To add brakes to the front axle on your trailer I would need to know the weight capacity of your axle (which can be found stamped on the axle if you don't know it off-hand), as well as the part numbers of your Inner and Outer Bearings and you Grease Seal on your idler hub. The bolt pattern of your hub and size of your tire/wheel would be helpful as well. If you cannot find the part numbers on your bearings or seal then you can measure the B, C, and D locations on your spindle (see attached...
  view full answer...
  
• Spindle Recommendation for a Hub that Has Bearing Dimensions 1.06 and 1.38
  The spindle we offer that has the closest dimensions to what you listed will be an 84 spindle like part # TRU64FR. The surface of the spindle where the bearings will ride is 1.06 inch and 1.38 inch which is pretty close to what you have but not exact so you would want to double check the measurements you took. For a hub then with the bolt pattern 5 on 4-1/2 inch like you said you need you would want the part # 84545BX.
  view full answer...
• Replacement Hub Components for Hub 9606020
  While the # L68149 most likely corresponds to the inner bearing number of your hubs. If this is the case, you have either a 3.5k or a 4.4k axle. In order to know absolutely sure, you need to know the corresponding outer bearing number or the inner and outer diameter of the grease seal. You most likely need to wipe away the grease in order to reveal the outer bearing number. In order to accomplish this, I recommend using calipers like the 4" Carbon Fiber Digital Caliper # PTW80157. I...
  view full answer...
  
• How to Determine Hub and Spindle Size
  The spindle dimensions are as follows: A is the mounting dimension, B is the seal dimension, C is the inner bearing surface, D is the outer bearing surface and E is the diameter of the threaded portion of the spindle for spindle nut selection. Say you need a spindle and hub for a wheel with 5 on 4-1/2 inch bolt pattern and an axle that is 3500 lbs. For a single axle trailer you can use two of either the item # TRU64FR, if your axle is round or item # TRU47FR if your axle is square. Then...
  view full answer...
• What Spindle Does Trailer Hub # AKIHUB-655-35-K Fit
  The trailer hub part # AKIHUB-655-35-K that you referenced is designed to fit a 84 spindle like the part # TRU64FR.
  view full answer...
• Replacement #84 Spindle for Dexter 3500-lbs Axle
  As long as you've got a 3500-lbs EZ Lube axle then you can use the #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter # TRU74FR to replace your spindle; if you don't have EZ lube axles then you'll want to use the #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter # TRU64FR and Brake Mounting Flange for 1-3/4" Round Trailer Axles - 2K # 4-34. Both of these spindles take # L68149 inner and # L44649 outer bearings. To replace the hubs you'll want to use...
  view full answer...
• Replacement Spindles For 3,500LB Trailer Axle With Tapered Spindle with 1-1/16" & 1-3/8" Bearing ID
  We do have the following replacement spindles that will fit on your axle. #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter # TRU24FR #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter # TRU84FR #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter # TRU64FR #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter # TRU74FR
  view full answer...
• Replacement Hub And Spindle For TieDown 3,500-lb Axles
  I spoke with Dexter Marine of Georgia, who bought the running gear portion of TieDown (axles, actuators, brakes, brake lines, spindles, leaf springs and hubs), and they mentioned that you can use a Easy Grease Trailer Idler Hub Assembly for 3.5K Axles # AKIHUB-545-35-G-EZ-K for replacement hubs, and you can use these #84 spindles, depending on the length of the spindle needed: -For a #84 spindle, with 8-1/4" overall length, you can use # TRU64FR. -For a #84 spindle, with 9" overall length,...
  view full answer...
• Availability Of 5-5 1/2 Inch Hub Assembly, Spindle, Bearings Rated For 1,750 lbs. Each
  I have the Dexter Trailer Hub Assembly - 3,500 lbs Axles - 5 on 5-1/2, # 84555UC1, which is rated at 1,750 lbs. each. The bearings, races, cap and seal included. The only other option I would have is the Dexter Trailer Hub & Drum Assembly - 3,500 lbs. Axles - 5 on 5-1/2, # 84557UC3, if you were wanting brakes. The capacity is 1,750 lbs. and comes with a 10 inch X 2-1/4 inch drum. It also comes with bearings, races, cap and seal. The spindles that are available for both hub assemblies...
  view full answer...
• What Size of Spindle is Needed for a 3,500-Lb Axle
  I have three spindles that are for a 3,500-lb axle and have the bearing dimensions you have listed. The only difference is the dimension for the grease seal is 1.75 inches, not the 1.795 inches that you have mentioned. Maybe you typed in the seal diameter wrong. The hub number you have mentioned is just a casting number, not a part number. The three spindles I have for a 3,500-lb axle are as follows. #84 Spindle - 1-3/4" Diameter (8-1/4" OAL) # TRU64FR #84 E-Z Lube Spindle w/ Brake Flange...
  view full answer...
• Spindles That Will Work With Dexter Trailer Hub Assembly # 84545UC1-EZ
  We offer 3 spindles that have the dimensions compatible with the Dexter Trailer Hub Assembly, part # 84545UC1-EZ. The first is part # TRU74FR. This is a 1.75 inch round EZ-Lube spindle with a grease fitting and a brake flange. This spindle has an overall length of 9 inches. The next is part # TRU64FR. This is a 1.75 round spindle that does not have the brake flange or grease zerk fitting. This spindle has an overall length of 8-1/4 inches. The third is part # TRU24FR. This is a 2 inch...
  view full answer...
• Replacement Disc Brake Trailer Hub With Rotor And Bearing Kit To Replace TRE 46245
  The Kodiak 10" Hub-and-Rotor Assembly # KHR10D matches the TDE 46245 that you currently have. The hub has a disc rotor and 5 on 4-1/2" bolt pattern. The Hub Bearing Kit # BK2-100 contains the races, bearings and grease seal for you to be able to mount it to a spindle like the #84 Spindle for 3,500-lb Trailer Axles # TRU64FR
  view full answer...
  

Do you have a question about this Trailer Spindle?