Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
The spring seat is a necessary component of your trailer's suspension system. When mounted with 1-3/4" wide leaf springs, it adds extra support and provides proper positioning for the axle.
Features:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to be taking a look at a spring seat for typical 2,000 pound, round trailer axles, with a 1-3/4 inch diameter. The spring seat is a necessary component of your trailer's suspension system. When mounted with a 1-3/4 inch wide leaf spring, it adds extra support and provides proper positioning for the axle. This unit's made from a durable steel construction. It welds on to a round 1-3/4 inch diameter axle, which is a typical 2,000 axle. It sits on top of a 1-3/4 inch wide spring. The cut out on the flat side of the seat surrounds the raised knob on the leaf spring to prevent turning or shifting.
It's going to provide extra support and secure positioning for the trailer axle. Please note that two spring seats are required for each axle. A few measurements to go over with you real quick. Start with the overall length, measuring edge to edge. It's going to measure about 2-1/4 of an inch long. Overall width, measures about 1-7/8 of an inch.
The height, is just shy of 1 inch, about 15/16 of an inch tall. Then this opening, right here, the rounded point, at the widest spot, that's going to give us an opening measurement of really close to an 1-1/2, maybe 1-7/16 of an inch, right in that area. That's going to do it for today's look at the spring seat for typical 2,000 pound, round trailer axles, with a 1-3/4 inch diameter.
Average Customer Rating: 4.8 out of 5 stars (139 Customer Reviews)
The spring seat is a necessary component of your trailer's suspension system. When mounted with 1-3/4" wide leaf springs, it adds extra support and provides proper positioning for the axle.I havent really gotten a chance to use the trailer much since my purchase of the leaf springs. But they went on perfect and the stance is perfect. With a weight load , they should be just right.
These brackets used in conjunction with the new u-bolt kit made switching my trailer axle from being above spring to under spring.
This has raised the trailer about 3 inches in height from stock. I have a new set of wheel and tires coming and this should take care of the slight slope as seen in the picture.
After installing everything, I took the trailer for a test drive and it tracked nicely and behaved very good on the road. No problems.
First and foremost, working with etrailer was a pleasure. They were veery helpful in many ways. Secondly, Theproducts I purchased were exactly what I needed. I flipped the axle on my utility trailer in order to beef up the springs and use larger tires. The u-bolt kits were oerfect, and after having the spring seats welded onto the axle the rest of the job went smoothly. All in all 5 out of 5.
Perfect for an axle leaf over mod. Welded on easily and appear very sturdy. I need to rebuild the hubs and complete the frame modifications before reinstalling the axle.
I was adding some supports to a trailer deck for a friend and noticed the spring seats were rusted away, found the parts quickly on etrailer shipping was fast and the trailer is ready to get back on the road.
The spring seats and u bolts kit were very reasonably priced and do the job they are supposed to do.
so far so good, just did a shake down test, all good. The trailer went straight and true. Now just waiting on my other order to come in so I can put some weight on the truck and trailer for the real test.
These nests are kind of hard to get wrong really. I welded them into position, haven’t thought about them since. So,… I mean,… that’s good right?
Super fast shipping
The only mistake I made was not ordering two axle saddles. I thought my order was for a pair, so I only ordered one. My mistake.
Solid, took a weld like a champ!
Plus:
Good products for a super low price. Accomplished the goal of bringing life back to a dead trailer. The leaf springs ride much better than the stock rubber torsion axle. The new hubs and bearings roll much easier than the worn out ones they replaced.
Minus:
A little disappointed in the spring bushing. It seemed like cheap plastic and was quite a bit larger than the bolt so it fit loosely. This was the only real negative I have about the purchased, and that's pretty minor.
Tips for etrailer:
Providing a height of the spring would make spring selection easier. In our case we were starting with scratch for mounting springs, no preexisting mounting hardware. Knowing the height of the spring from mount to axle would have been helpful in selecting a spring for the proper ride height. In a snowmobile trailer application an inch or two in height makes a bit difference in approach angle when loading a sled. This was about the only measurement not listed for springs so we guessed, and it came out well for us in the end.
Exactly what I needed.
Bought these along with the UBolt kit for a Coleman popup camper to do an "axle flip" or move the axle from above the springs to below the springs giving 3-4 inches of additional clearance. My popup has a 1.75" axle and Dexter doesn't make prefab kits for that axle. Spring seats had to be welded to my axle, but beyond that, the axle flip worked OUTSTANDING! If you go off road at all with your camper, I can't recommend enough doing this. Should have done it years ago! Spring seats worked great!
John H.
6/5/2015
I ordered a couple of the 1- 3/4 U bolts from eTrailer as well. Yes, weld up the perches opposite the old ones but be sure to take some time to make sure theyre aligned both vertically and horizontally. I used a level to compare the top plane of the new perches with the bottom plane of the old ones with the axle upside down and clamped it in place before welding.
I purchased a number of products from etrailer and I am very pleased with them all. The shipper lost my axle. When I contacted etrailer customer service, they handled my problem quickly and I had a replacement axle in a couple days. Well done!
The products were all of high quality and the assemble was much easier as a result. I have attached a few pictures of the build for those interested.
Thanks etrailer for your great products and service!!
Jim D.
1/2/2021
The trailer has performed better than my expectations. The products I purchased are all performing perfectly. When I build my next trailer, I will get all my assemble products from etrailer.com
The parts that fit the axel where included on the axel page and where just what I needed to adapt the axel to a smaller with trailer
Needed "spring over" conversion on Teardrop type camper. Dexter axle required these to do it right. Perfect fit. Time from order to shipping was longer than anticipated. So parts, availability and knowledge are great, delivery time disappointing.
Thom K.
7/7/2015
Product is great. No problems whatsoever. I heartily recommend etrailer and will use them for my next camper buildconversion.
Highest quality. These are stout!
Richard
5/14/2023
A year later and the axle is working just fine. I love the easy lube spindles. So easy and mess free.
Thank you for exactly what I needed at a fair price.
Shipped to me in a timely manner so I was able to the job I was working on.
Your website was very user friendly as well.
keep up the good work.
Jim J , Wisconsin
Jim J.
8/5/2016
Thanks for checking All working as needed
Works as advertised. I had a local welder put these onto the axle for me. I ended up needing them since my harbor freight trailer had a metric dimensional spacing between the mounts and the axle I bought had a standard inches dimensional spacing. They were off by less than 1 inch, but I couldn't make it fit unless I welded on these brackets at the correct location for the trailer.
Great product for mounting spring on top of axle just remember you have to weld them on
Donald K.
1/25/2017
Really happy with purchase great price a only had to buy spring mount pads to mount on opposite side of axle
Donald K.
1/25/2017
Love the product have order more for other projects
Worked out just rite, had to setup an over/under to raise trailer. Added about 3" to the ground clearance
Paul M.
9/18/2016
great
Seems like quality metal. Was easy to get them welded on. Confirmed great to my 2000 lbs axle, no issues.
Shawn
4/14/2021
Everything is still great, no issues.
I have a Coleman Tent trailer and our favorite camp sites are off road. I decided to flip the axle to gain some off road clearances and level the trailer being towed by either my Truck or Jeep which have lift kits. I purchased these parts, installed and I am stoked! Great product and was easy to install. Parts were of great quality and shipped quickly. I will most definitely trust etrailer and highly recommend them. Thanks etrailer!!
Do you have a question about this Trailer Suspension Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Dc
6/2/2015
Hey John, Im about to do the same thing to my 89 Coleman pop up. What u bolts did you use and what other items did you need? Just weld these opposite of the old ones and replace springs with u bolt?