U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts
(829 reviews)
Price: $44.73
In Stock
U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts
Item # APUBR-1
Retail:$74.28
Our Price: $44.73
You Save: 40%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (829)
- Q & A (0)
- Videos (2)
- Photos
Dexter Trailer Suspension Parts - APUBR-1
- U-Bolt Kits
- Camper
- Car Hauler
- Utility Trailer
- Round Axle - 2-3/8 Inch
- 5-1/2 Inch Long
- 3500 lbs
- 1/2 Inch Diameter
- Dexter
Mount your round, 2-3/8" diameter axle to your trailer's leaf springs with this U-bolt kit. U-bolts, plates and nuts included.
Features:
- Attaches trailer axle to leaf springs
- Includes:
- (4) 5-1/2" Long U-bolts (176400)
- (2) U-Bolt plates for 1-3/4" springs (117595)
- (8) 1/2"-20 Hex nuts (12N)
- Spring seats required for mounting axle to leaf spring sold separately
Specs:
- Axle diameter: 2-3/8"
- Typical 3,500-lb axle
- Spring width: 1-3/4"
- Dimensions: see below
K71-731-00 U-Bolt Kit for 3,500-lb Round Trailer Axles
Replaces APUBR-1
Video of U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Trailer Axle Long U-Bolt Mounting Kit Review
Speaker 1: Today we're going to be taking a look at the Redline U-bolt kit for mounting 3500 pound round trailer axles. These are 5 1/2 inch long U-bolts. The part number is APUBR-1.Now, when replacing your axle, it's a really good idea to also replace the U-bolts. These are a pretty cost effective item you can get and ensure that you're going to have excellent, excellent hold with your axle to your springs. You can see this is going on a floor spring pack. The opening on them is going to be 2 3/8 inch, so it's going to fit the outer tube diameter of our axle here.
It comes with the new lower plate, and also four new flange nuts that allows you to secure that end, keep everything locked tight, so you don't have any issues for a very long time.Now we're going to remove the four nuts on the bottom here that hold our axle down, and they hold the U-bolts here. When replacing an axle, generally you're going to replace these as well, just because these can kind of stretch over time. So, if these nuts won't come off, you can also just cut your U-bolts on each side.Now we're going to grab our new U-bolt kit and place these down and around, just like our old U-bolts were, and when we we'll replace the bottom bracket up on the U-bolts we'll see the hole here in the middle. That's meant for that nut to come down through, and then in each position we'll install one of the flange nuts.Now we'll go through and you're evenly going to tighten down our bolt. We'll get them snugged up first and then we can torque them.
For these nuts you'll want to use a 19 millimeter 3/4 inch socket. Notice we're tightening them evenly, but in a crossing pattern.That's going to compete our look at the U-bolt mounting kit for 3500 pound round trailer axles, part number APUBR-1.
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- etrailer mistake
- Did not arrive in time
Customer Reviews
U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts - APUBR-1
Average Customer Rating: 4.8 out of 5 stars (829 Customer Reviews)
Mount your round, 2-3/8" diameter axle to your trailer's leaf springs with this U-bolt kit. U-bolts, plates and nuts included.by: Joseph02/04/2024
These did not fit my 3500 lb axle. It has been very difficult determining the correct size U-Bolts for my axle. It appears etrailer does not carry the size I need.
by: Bill 12/04/2022
It is exactly as described. It seems solid. I also ordered the springs, and they appear to be solid as well. I look forward to continuing to do business with etrailer due to quality parts AND great customer service from the likes of Shawnee and the crew. Thank you!!!
Bill
12/6/2023
It’s been a year and the trailer is as good as new. The leaf springs have held up well after many trips across the desert several miles of unpacked road and into town 80 miles one way to haul in materials cinder block, Portland cement, etc to finish building my house. Just bringing an empty load across these roads is abusive to any trailer, but many, many full loads later and the trailer is doing great! Thank YOU!
by: Ben R06/14/2014
I recently replaced my 1/2 ton truck with a 3/4 ton truck. In order to hook up to my existing fifth wheel camper, I had to raise my camper. To do this, my brother and I moved the axles from the top of the leaf springs and attached them under the springs. This kit made it very easy to do this. We torched off the old u bolts and used this set as a replacement. The quality of this kit was very good. Hard to get too excited about u bolts but I would purchase this again if I had to do it all over again.
I was able to gain about 5 1/2 inches by flipping the axles. Here is a before and after.
by: Mike06/21/2023
STEEL PLATES WERE DRILL BUT NOT ROLLED/FORMED LIKE ORIGINALS. PLATES STARTED TO BEND BEFORE REACHING 60 FT LBS. ORDERED ON JUNE 8TH DID NOT RECEIVE UNTIL JUNE 2OTH. VERY UNIMPRESSED!
by: Hank S.06/12/2018
I replaced the rusted out U bolts on my 5x8 utility trailer with this kit, APUBR-1 from Redline. The kit fit great, no problems. Good quality parts. Great price. Would buy from etrailer again.
by: Anthony L12/03/2022
Everything worked great---All the correct parts ---the best place to buy parts.
very good service thanks to James. YEA
Janet L.
12/3/2023
working great no problems!
Mike L.
12/3/2023
@JanetL We're glad to hear that!
by: Robert11/12/2023
The springs were a perfect match up. Easy installation with the exception of my existing rusted bolts Prompt service, exact replacements would not hesitate to use etrailer for any parts for my three trailers
by: Troy02/07/2023
This was used to replace original factory parts that were completely worn out. I am extremely happy with the parts I received. Everything worked like it was supposed too
by: Peter11/22/2023
This set of leaf springs was excellent choice for my 4’x8’ utility trailer, handles great.
by: Richard 12/02/2023
The order was shipped like the day after it was placed. Everything seems to be high quality. There was even a color brochure that described the entire installation. Even though I was the distinguished honor graduate from my Alma Mater (Real Men Don't Need Instructions) I did read the pamphlet and found the instructions and tips to be very helpful.
by: Rob 05/28/2024
Got here quickly. Have not had a chance to install yet, but should be no problem.
by: JW05/10/2024
It works as advertised….. what more do u need?
by: Joe N.02/24/2017
replaced my old axle and hubs with a heavy duty axle, U-bolts and new hubs. It has all held up well. I had to custom weld the axle carrier to fit my trailer, but everything fit well, and was a fairly easy installation. I now feel much more confident with a 3500 lb. axle and these heavy duty U bolts under my trailer.
by: Robert10/18/2023
etrailer always has what I need in stock. And the parts are high quality. Plus their professionals always have sound advice and recommendations for me. They are a one stop shop! Than You etrailer!!
by: Bruce 12/17/2023
The kit was perfect to replace my original equipment on my 2007 trailer.
by: Lawrence 10/10/2023
I was shorted to you, Walts I called customer service. They immediately took care of it and shipped me out a new product. I’ve got to admit the quality of the product is great and the customer service is even better. Thank you E-trailer .
by: Allen03/18/2018
Last project built. Used etrailer for almost all parts, 7 pin wiring harnesses, junction block, tail lights, jacks, spring retainer bolts vent cover and so on. Love the leveling jacks. Friend wants one now so started another one. I will be getting all the parts from etrailer...
by: Gary 10/30/2023
Easy installation and have worked just fine every since.
by: Tom 07/17/2023
These axle u-bolt mounting kit worked great and did exactly what it was supposed to do. Install was easy and it contained the parts that I needed.
by: Jeff05/05/2022
Parts fit as advertised, very satisfied with purchase. I new nothing about replacing a trailer axle info on web site and support provided were excellent.
Definitely would recommend etrailer
by: Sgtbass6412/10/2015
Fit perfectly for my trailer. All the components seem to be heavy duty.
Sgtbass64
12/9/2016
Well, its been a year and I am still very impressed with the suspension parts I got from eTrailer. I have ran my car trailer from Michigan down to southern Ohio, Indiana, and Illinois. Had no issues what so ever. The trailer handled beautifully.
by: Tom03/19/2022
It was so nice to work with new and proper fitting mounting bolts. Everything I needed to attach the axles was in the kit.
by: William05/26/2023
Purchased several axle and suspension/mounting parts from etrailer. Parts are always of good quality and work well. Shipping times are always reasonable. Plan to continue using them as a supplier for my trailer parts.
by: Jesse 04/15/2024
Very good, bolts right on.
by: Bob P04/05/2024
I love the constant communication with Lori!!
25
829
Show More Reviews
See what our Experts say about this Dexter Trailer Suspension Parts
- TRAILER SPRINGSFor the large 8000 lb. springs you want to use U-Bolt Kit for Mounting 8,000-lb, Round Trailer Axles part # APUBR-35 and for the smaller 3500 lb. springs use the U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles part # APUBR-1. Thes will give you the u bolts, nuts and the new plates so you will be set.
view full answer... - Choosing a U-bolt Kit for Trailer with 1-3/4 Inch Wide Leaf SpringsWhen choosing a U-bolt kit for you trailer, you want to choose the correct kit based on the size of your trailer's axle. The width of the leaf springs isn't the main factor. The U-bolt kits you referenced will not both work on the same trailer axle. The # APUBR-8 kit can accommodate both 1-3/4 inch and 2 inch wide springs, but it is designed for use on 3 inch diameter round trailer axles that have capacities between 5,200 pounds - 7,000 pounds. The # APUBR-1 kit will accommodate 1-3/4...
view full answer... - Recommended Trailer Axle Capacity Upgrade and Position of AxlesAbsolutely. I've attached some articles on axle location to assist as you shorten the trailer. For your axle, you can use the Timbren Axle-Less Trailer Suspension System - Spindle w/ Brake Flange - Regular Tires - 7K # TASR7KS01 for a single axle application. This will make it easy for you as you don't need to worry about hangers, springs, etc. It will simply bolt to your frame and then you run a 2 inch square bar between them into the integrated holes. For a tandem axle assembly,...
view full answer...
- Trailer Suspension Kit and Leaf Springs Recommendation for a Tandem Axle Boat Trailer 4,600 lbsAs long as you are replacing everything (hangers, springs, hardware, equalizer), then yes, you can use our trailer suspension kit, # APT5. In fact, this is the kit that I recommend for your trailer. The hangers must be welded to the trailer. The holes that you see in the top of the hangers are actually for welding, not bolt holes. For the leaf springs, you will be much happier with the ride quality of part # e54SR for 3,500 lb axles. The other springs you referenced are for 5,000 lb axles,...
view full answer...
- I Need Replacement Leaf Springs for 3,500 lbs Double-Eye Springs 26-1/4 Inches LongAssuming your springs have some age and some mileage on them, then they were likely 25-1/4 inch long springs. That is the typical size for 3,500 - 4,000 lbs double-eye leaf springs like part # e57SR. These are the springs I would go with if I were you. If you also need a new u-bolt kit, then I recommend part # APUBR-1
view full answer... - Replacing A Dexter Axle With Higher Load Rating Dexter AxleFrom the information you have given me, if I am correct your current axle should be 89" long when measured from hub face to hub face and from one spring center to the other is 74". To up grade to a 3500 lb axle without modification you need Dexter Trailer Axle Beam with EZ-Lube Spindles - 89" Long - 3,500 lbs Item # T3584F-EZ-8974. All measurements are going to be the same and should not require any modification. Going up in size will require a U-Bolt Kit for Mounting 3,500-lb, Round Trailer...
view full answer... - Replacement Hubs and U-Bolt Kit for 3,500 Pound Lippert Axle # LC35212150From my research your axle is a 3,500 pound, 2-3/8 inch diameter axle and since you have a 5 on 5 bolt pattern you likely have bearings # L44649 and # L68149. You'll want to verify this is correct with your current bearings. If this is the case for a hub and drum assembly I recommend # AKHD-550-35-EZ-K which is for E-Z Lube axles with a zerk fitting. If you have standard axles use # AKHD-550-35-K instead. If you only need idler hubs use # AKIHUB-550-35-EZ-K with E-Z Lube axles and #...
view full answer... - Recommended Trailer Axles and Suspension for BBQ-Smoker Trailer with Pit Weighing 3,000-3,500 lbsFor your BBQ smoker trailer you are building, a single 5200 lb axle will work just fine. There are no requirements for single versus tandem axle applications. The biggest thing to consider is the stability of the trailer. I personally would be more comfortable grilling with the weight of the smoker over 3 contact points versus 2, so I recommend using the Dexter Trailer Axle w/ Electric Brakes # 35545E-ST-89 along with the Tandem-Axle Trailer Hanger Kit for Double-Eye Springs # APT3 and...
view full answer... - U-Bolts and U-Bolt Plate Recommendation for Installing Leaf Springs on a 1-1/2 in Square AxleIf what you really need is a new axle you can go to a local trailer shop to you and have them custom order you the exact specs you need for a trailer axle. But to attach springs to your 1-1/2 inch square axle you would want the mount plate part # 115983 and then for U-bolts part # Sp01-120. I attached review videos for both products.
view full answer...
- Leaf Spring Hanger Kit for Lippert Double-Eyed Springs on a Custom Car DollyI would be happy to help you find the mounts you need to complete your suspension system. For the 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/8" Long item # e54SR, you're going to want to use the etrailer Single-Axle Trailer Hanger Kit for Double-Eye Springs item # APS4. You will want to have 24 7/8" from bolt hole to bolt hole between the trailer hangers. You will also need the Redline U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts item # APUBR-1. The...
view full answer... - Can a Three Leaf Spring Stack Be Used To Replace a Two Leaf Spring StackYes, you can replace a two leaf spring stack with a three leaf spring stack so long as your center to center (double eye springs only) measurement matches but please note the loaded and unloaded as well as the new and used center to center measurements will be different. There is a correlation between the numbers of leaves in a stack and the weight capacity of that stack but there are also two leaf spring stacks with the same weight capacity as three leaf spring stacks so going by the rated...
view full answer... - Replacement Suspension Parts for Tandem Axle Travel TrailerThe 3,500 lb axle is the most common size 2-3/8 diameter axle, but it isn't the only one. If you have the odd-ball 2,800 lb axle, then you will have the different bearings, seal, and hubs you referenced because of the spindle dimensions. Each axle is rated individually by the manufacturer and the spindles are in the case the reason for the lower rating. The springs you currently have are not available from our manufacturers in the size. You will need to replace the hangers as well...
view full answer... - Recommended Suspension Parts Needed To Build A Smoker TrailerLooks like you have quite a project going here. After consulting with other Experts, the first thing I would recommend is a new axle for your trailer frame. It appears the axle you have was originally used on a car and welded to the trailer. I could not recommend any suspension that could safely be used with the axle in your photos. I have attached a help article that explains how to determine the correct axle position. The next thing to consider is that you will have to build your trailer...
view full answer...
- Recommended Axles For Tandem TrailerThe axles we carry that are closest to the size you mentioned are our 89 inch axles, like the etrailer Trailer Axle w/ Electric Brakes # e43SR. This is an easy grease axle with electric brakes and the hubs have a 5 on 4-1/2 bolt pattern. This axle measures 89 inches hub face to hub face and the spring-center-to-spring-center length is 74 inches. This comes with the bearings, races, seals, grease caps, studs, lug nuts, and the hubs and drums. The axle with idler hubs and no brakes that...
view full answer... - Axle U-Bolt Kit for Single 2-3/8-Inch Diameter Trailer AxleWe have many sizes of round and square axle u-bolt kits that appear on the linked page. These are not rated by weight so you simply want to choose the one to match your axle diameter, which should be 2-3/8-inches. U-bolt kits # APUBR-1 or # CE23002 will do the trick.
view full answer... - Recommended Replacement Leaf Springs and Hanger Kit for 8,000 Pound Dual Axle Car HaulerStarting with the leaf springs, I recommend the 3-Leaf Double-Eye Spring # e57SR. This 3-spring stack measures 25-1/4 inches from the center of spring eye to the center of spring eye. This is a more common spring length for this capacity, so it will be much easier to find an exact replacement down the line when needed. You can then use the Tandem-Axle Trailer Hanger Kit # APT5.. This kit includes 6 hangers, 2 equalizers, 8 shackle straps, 14 shackle bolts, and 14 locknuts. You will need...
view full answer...
- Leaf Spring Replacement Solution for 2017 Keystone LaredoAs long as the 26 inch length of the leaf spring part # e27SR matches what you have now this spring would work great. The difference in the amount of leaves would not be an issue at all. Most likely you have 2-3/8 inch diameter axles and the correct U-bolt kit would be the part # APUBR-1 but if you have something different let me know.
view full answer... - U-Bolt Plate Width For Leaf Spring Mounting on APUBR-1The width dimension of the U-Bolt Kit for Mounting 3500-lb Axles # APUBR-1 is 2-3/8", which is the typical diameter of a 3500-lb axle. These can be used to mount leaf springs 1-3/4" wide to an axle when used with with the included plates and Spring Seat for Typical 3500-lb Round Trailer Axles # TRSS238 . I've attached a picture for reference on these measurements.
view full answer...
- Why is the Dexter Over-Under Conversion Kits for Double Eye Leaf Springs OnlyThe Dexter Over-Under Conversion Kit, # K71-384-00, is recommended for double eye leaf springs only because it is a bolt-on kit. Slipper springs require the spring seats to be welded to the axle. You could use this kit if you weld the spring seats in place. If you go this route, I recommend having a qualified welder complete the installation to make sure the spring seats are welded properly. Since the spring seats must be welded in place, you could save some money by simply buying two...
view full answer... - Grade of U-Bolt in the U-Bolt Kit APUBR-1The U-bolts of the U-Bolt Kit part # APUBR-1 are Grade 5. I attached an install and review video for this kit for you to check out as well.
view full answer... - Parts Needed to Turn Single Axle Trailer Into Tandem Axle TrailerThere is not going to be a kit, per se, to make your single axle trailer a tandem axle trailer because not all trailers are created equal. The first thing you'll need is the measurement of your current axle from hub face to hub face, and then spring seat center to spring seat center; this will determine whether or not you'll be able to use a stock axle or need a custom ordered one. The other parts you would need are a hanger kit like the # APT5 to mount the springs to the trailer frame,...
view full answer...
- Leaf Spring, Hanger Kit and U-Bolt Kit Recommendation for Building Pontoon BoatIf your trailer requires spring centers that are 70 inches and hub face to hub face dimension of 85 inches we do not carry the axle you would need, but you can find a local trailer shop who can custom order you in axles to the specs you need. Your best option would be to go with a spring setup that would match the weight you plan to tow. The # e84SR has a 2,000 lb axle rating and would be your best option. For a tandem axle hanger kit you would want the part # APT5. The hardware you would...
view full answer... - Recommended Axle And Fenders For Karavan TrailerThe 3,500 lb axle we offer that meets the 82-5/8 flange to flange measurement you mentioned you need is part # T3584F-8974. The spring to spring measurement for this axle is 74 inches. None of the axles we offer in this weight capacity have the 76 or 78 spring-to-spring measurement. The U-bolt mounting kit I recommend is part # APUBR-1. This includes the U-bolts, plates, and hex nuts needed for installation. If you are looking to buy new springs for your trailer you can check out the...
view full answer... - How to Choose Replacement Springs and Axle for a Trailer with a 3,500 Lb AxleIn order to determine the correct trailer axle for you I would need to know the distance between the spring seats as well as the distance between the hub faces on your trailer. For example, the Dexter Trailer Axle Beam with EZ-Lube Spindles part # T3584F-EZ-8974 has a 74" spring center and 89" hub face with a 3,500 lb capacity. The correct u-bolts for this axle is part # APUBR-1. If you trailer does not match the above dimension then I recommend using the Timbren Axle-Less Trailer Suspension...
view full answer...
Do you have a question about this Trailer Suspension Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Video by:
Kathleen M
Video by:
Zach D
Installed by:
Cole B
Installed by:
Randy B
Installed by:
Andy C
Video Edited:
Chad S
Video Edited:
Chris R
Updated by:
Wilson B
Updated by:
Alexander C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jenny N.
2/6/2024
It is true that we do not carry all sizes of u-bolts. The best way to determine what you need to take a few measurements. First, you want to check to see if you have a round versus square axle. Second, using your old u bolt, measure the width on the inside of the u bolt [between the bolt arms]; this will match the width or diameter of the axle. Secondly measure the length of the bolt arm. This depends on the axle diameter and number of leaves on springs. The u-bolts must be long enough to clear the axle, spring seat, and springs. Last, you want to measure the diameter of the bolt arm. Please see the FAQs below, one for double eye trailer suspension and one for slipper spring suspension that will go into more detail.
Helpful Links
faq-double-eye-trailer-suspension-review.aspx
faq-slipper-spring-trailer-suspension-review.aspx