Erickson Horizontal E Track - Zinc Plated Steel - 2,000 lbs - 2' Long - Qty 1

See what our Experts say about this Erickson E-Track

• E-Track Setup to Secure Lamp Boxes in a Trailer
  For securing cardboard lamp boxes that are both 4 and 8 feet long with e-track like part # EM59150 your best option would be to go with e-track D-rings like the part # E59143 and then a tie-down set like the # 05605.
  view full answer...
• Recommendation for Securing Two Different Sized Polaris RZRs to Trailer
  To secure your Polaris RZRs to your trailer, I recommend installing the Erickson Horizontal E-Tracks like # E19148. This zinc coated steel E-Track is 5 feet long but shorter lengths are available with the 4 foot # EM19147 or the 2 foot # EM59150. Once installed, these tracks will provide multiple slots for securing your RZRs with the Erickson Adjustable Wheel Nets # 77314. The tracks provide a safe working load limit of 2,000 pounds and a maximum load (break strength) of 6,000 pounds. This...
  view full answer...
• Mounting Suggestion For E-track To Aluminum Utility Trailer
  For your Aluma 6810 HBT trailer, I recommend the Erickson Horizontal E-Track - Zinc Coated Steel - 2,000 lbs - 5' Long - Qty 1 # E19148 along with the E-Track Backing Plate - Zinc Plated Steel - 6" Long x 6" Wide # e96RR. This will save you the expense of the dual track and will allow you the flexibility of plates between the braces or around them. This track also comes in 4 foot # EM19147, and 2 foot # EM59150. I recommend using the E-Track Plastic End Cap # ET8730 to finish your tracks. For...
  view full answer...
  
• Using Erickson E-Track on Floor of Snowmobile Trailer
  The Erickson E-Track is pretty rugged stuff, I doubt that the snowmobile track would crush it. Because of the studs, you might consider installing the etrack so that its let into the floor so that the face is flush with or slightly recessed from the floor. We do not offer the etrack in different colors, its available in raw steel like the # EM59150 or in zinc plated as part # E19148.
  view full answer...
• Recommendations for Anchoring E-Track to a Ply-Wood Trailer Floor
  It depends on how much load you will be applying to the track, what you are holding with it, and how the trailer frame is made. If you can get to the trailer frame, use nuts and bolts to attach through the floor and the metal trailer frame. If you are using it to secure an ATV or 4-wheeler, mount the track where the ATV tires will rest on it and the weight of the ATV will hold the track down. This way you would only need a handful of attachment points just to keep the track from sliding. If...
  view full answer...
• Can Erickson E-Track Be Used on Exposed Deck of Open Utility Trailer
  Erickson E-Track Cargo Control items like # EM59150, # E19148 and # E19146 are not painted but rather they are given a zinc coating treatment to provide corrosion resistance since they are made of steel. These are perfectly suitable for use on the deck of an open trailer. Be sure to use appropriate non-corrosive galvanized hardware to install the tracks. No fewer than 2 fasteners per linear foot (on each side) are required.
  view full answer...
• Anchoring E-Track On Floor Of Van For Transporting a Motorcycle
  To secure the Erickson Horizontal E-Track # EM59150 you need to use the E-Track Backing Plates # e66RR to secure them to the floor. The screws can easily pull out of the plywood especially considering your van will be absorbing a lot of road shock. You will want to ensure that the plywood is also secured to the floor either with the backing plates or in another similar manner. This will ensure that your Harley stays secured to the floor and will not move. I recommend using the Erickson...
  view full answer...
• Mounting E-Track for Hauling Motorcycle on 8 x 5 Trailer
  That's a great question. I believe your installation method for the Erickson Horizontal E-Track # EM59150 sounds like a great plan as long as you have the tracks facing the direction of travel. Basically the E-Track was designed around this and that is the most safe way to secure cargo. To secure your 900 lb bike you can either use the Erickson E-Track Tie-Off w/ D-Ring # E59143 with your current ratchet straps or you can update to the Erickson E-Track Strap with Ratchet # EM59136 which...
  view full answer...
  
• E-Track Recommendation for Installing on the Inside of a Carson Fun Runner Toy Hauler
  Sounds like a good plan. For the 5 foot sections of the E-track you would want part # E19148. The # EM59150 that you referenced is sold in 2 foot sections. You might also be interested in the E-Track Tie-Off Ring # 59131, E-Track Wood Beam Socket # 59149, and E-Track 2" D-Ring part # E59143.
  view full answer...
• How To Attach the Erickson Horizontal E-Tracks To Wood Deck Boards
  In order to attach the deck boards to your open trailer, I recommend using 1/2" carriage bolts. These carriage bolts can be either zinc plated or made of stainless steel. They will need to run though both the deck board and trailer frame. In order to then attach the Erickson Horizontal E-Track part # EM59150 so you can use the Erickson ATV E-Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks part # EM09160, I recommend using standard grade 5 or higher 1/4" hex head bolts along with the...
  view full answer...
• What is the Weight Capacity of the CargoSmart Motorcycle Wheel Chock for E-Track Systems
  I reached out to CargoSmart and found that there is no weight capacity rating for the CargoSmart Motorcycle Wheel Chock for E-Track or X-Track Systems # 3481731 since it is only meant to stabilize your motorcycle. The limiting factor would be the E-track in this case. Assuming you are using the single slot E-track tie-down points like the Snap-Loc E-Track Tie-Down Anchor # SLSB you shouldn't have any problems. Although I do not know the capacity of what you have, each of these has a safe...
  view full answer...
• Can E-Track Attach to Diamond Plate
  As long as you securely attach hardware on the back side of the diamond plate e-track like # EM59150 will attach just fine to it.
  view full answer...
• Operation of Locking Release Tab on Loc-Ring for Snap-Loc E-Track Tie-Down Anchor # SLARI
  The Loc-Ring for Snap-Loc E-Track Tie-Down Anchor # SLARI has a spring-loaded tab that is pressed in toward the O-ring to allow it to be inserted into an E-Track receptacle. The tab also needs to be pressed in for removing the O-ring from the E-Track. If you wish to add or replace some of the E-Track in your trailer we offer both 5-foot, part # E19148, and 2-foot lengths, part # EM59150. When installed on the floor of your trailer, the top surface of the E-Track will extend above the...
  view full answer...
• Attaching Galvanized E Track to Flooring In Trailer
  I would recommend using the galvanized lag bolts you refer to. Due to the thickness of the floor, I do not think it would be necessary for all the lag bolts to go through the flooring and bolt to the frame, but having the 4 at each end and two in the center would be a good idea. The remaining bolts, spaced an one foot intervals could be driven into the 2x8 planks. The galvanized e track would hold up well to the weather.
  view full answer...
• Can Self Tapping Screws Be Used for the Erickson Horizontal E-Track
  The Erickson Horizontal E-Track part # EM59150 can indeed be installed with self tapping screws. In regards to the number, most don't do every hole but there isn't really a required number either. It just comes down to the installer and application. I think every other hole would be just fine.
  view full answer...
• Weight Rating of Erickson E-Track Cargo Control Track EM59150
  The Erickson E-Tracks such as 5-foot-long # E19148 and 2-foot # EM59150 are rated for 2000-lbs. This rating presumes that the mounting surface you attach them to and the fasteners you use are also rated at least for this much weight. Installation of E-Track should use no less than 2 fasteners per linear foot per side. The tracks clearly do not have the capacity to suspend your 18K-lb load and the trailer wall itself will need to be really strong to hold a load like that. Depending on your...
  view full answer...
• Using E Track and Wheel Nets to Secure Vehicles During Transport
  I would recommend installing the 5 foot sections of E Track, part # E19148 directly to the cargo floor of the truck. You could then use a series of Wheel Nets, part # EM58523 to secure the vehicle wheels to the E Track (4 per vehicle, 4400 lb capacity per 4.) The method of securing the E Track to the truck floor will depend on the construction of the floor itself. The more fasteners used, the stronger the installation. You'll want to make sure some of the fasteners go into the trailer...
  view full answer...
• Using The E-Track Trailer Cargo Control # EM59150 On Trailer To Secure ATVs and Motorcycles
  Installing the E-Track Trailer Cargo Control, part # EM59150, would work well to strap down your ATVs and motorcycles on your V-nose trailer. You could mount the E-Track sideways or perpendicular to the trailer frame over the floor as you described. The E-Track can also be mounted on the wall of trailers, so perhaps you could mount the track for the ATVs on the floor towards the front of the trailer. Then you could mount track on the trailer walls for the motorcycles or on the floor as...
  view full answer...
• How Much Does the Erickson Horizontal E-Track # EM59150 Weigh
  The 2 foot section of Erickson Horizontal E-Track # EM59150 that you referenced only weighs about 1 lb.
  view full answer...
  
• Differences Between Horizontal and Vertical Erickson E-Tracks
  Erickson E-Tracks are offered in various lengths and for either horizontal or vertical installation on your trailer's deck or interior walls. An example of a vertical E-Track is part # E19146 and examples of a horizontal track are part # EM59150 and part # EM19147 that you referenced. You'll notice that the direction of the slots does differ. You will want to use 2 fasteners minimum per linear foot of track. Use fasteners on both sides of the track. So for example, a 2-foot track section...
  view full answer...
• Available E-Track Cargo Control Parts for Trailer Use
  If you are referring to E-Track parts like # E19148 and the related accessories shown on the linked page these tracks can be mounted to many different surfaces. The thickness and material of the surface determines the type of hardware to use. We recommend two fasteners per linear foot per side on the track. So for example, a 2-foot length of E-Track # EM59150 would need no less than six fasteners. If you have something else please respond to this email with photos of your load bars and...
  view full answer...
• Availability of Removable Wheel Chocks For ATVs To Mount on Trailer Floor
  The motorcycle wheel chocks we offer, such as the # TWSPWFKM are compatible with tires up to 6-1/2 inches wide, so they wouldn't be a good alternative for your ATV. We do have some alternatives that could work well for you though. The # PK-WTD from Pack'Em includes 2 chocks, the strap and mounting hardware. The chocks are permanently mounted, but they only sit about 1-5/8 inches off the floor, so they won't get in the way. Using E-Track like part # E19148 for a 5 foot length, # EM59150...
  view full answer...
• Available Lengths of Erickson E-Tracks
  Unfortunately, 5 feet is the longest Erickson e-track we carry and is # E19148. They also come in 2 foot # EM59150 and 4 foot # EM19147 lengths. They can be cut to the needed length.
  view full answer...
• Dimension of Inner Slot on Erickson E-Track
  Good news, I can help you with this measurement for the e-track. I have attached an image to this page for you to better see the measurements that I got. The length of the inside of the bracket is 2.45 inches and the width is .58 inches , these measurements were taking with a caliper like # PTW80157.
  view full answer...
  

Do you have a question about this E-Track?