Roadmaster High-Low Adapter for Tow Bars - 2" Hitches - 4" Rise/Drop - 6K GTW, 200 lbs TW
(182 reviews)
Price: $90.18
In Stock
Roadmaster High-Low Adapter for Tow Bars - 2" Hitches - 4" Rise/Drop - 6K GTW, 200 lbs TW
Item # RM-070
Our Price: $90.18
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (182)
- Q & A (0)
- Photos
Roadmaster Accessories and Parts - RM-070
- Tow Bar
- Hitch Adapters
- High-Low Adapter
- Roadmaster
- 4 Inch Rise/Drop
- Fits 2 Inch Hitch
Make up for the height difference between your RV and towed vehicle with this hitch adapter. Provides either a 4" drop or a 4" rise for high or low ground clearance. Hollow shank is lightweight.
Features:
- Allows for proper positioning of tow bar
- Makes up for height difference between RV's hitch and towed vehicle's base plates
- Also lets you mount a bike rack, cargo carrier, or other 2" hitch accessory
- Provides either drop or rise for adequate ground clearance
- Constructed of sturdy steel
- Hollow shank is lightweight
- Resists rust and corrosion with black powder coat finish
- Hitch pin and clip or hitch lock sold separately
- Made in the USA
Specs:
- Application: 2" x 2" trailer hitch receivers
- Drop/rise: 4"
- Receiver: 2" x 2"
- Tongue weight: 200 lbs
- Gross towing weight: 6,000 lbs
- Length:
- 6" From center of hitch pin hole to angled brace
- 10-1/4" From center of hitch pin hole to center of pin hole
- Limited Lifetime Warranty
Note: This adapter is designed to flat tow a vehicle only. Do not use to tow a trailer. When using with a hitch-mounted accessory, such as a bike rack or cargo carrier, the tongue weight of your hitch will be reduced by at least 50 percent.
Most tow systems require some sort of hitch accessory to either raise or lower the tow bar to an appropriate level. The "Safe Zone" for a motor-home-mounted tow bar ranges from 3" above level to 3" below. Car-mounted models must be absolutely level. This high-low adapter can provide you with the necessary drop or desired rise to achieve a level tow bar setup.
070 Road Master Hi-Low Hitch Adapter - 4" - 6,000 lbs GTW; 200 lbs TW
Installation Details
Customer Satisfaction Score:
95% were satisfied with this product
5% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Defective
Customer Reviews
Roadmaster High-Low Adapter for Tow Bars - 2" Hitches - 4" Rise/Drop - 6K GTW, 200 lbs TW - RM-070
Average Customer Rating: 4.9 out of 5 stars (182 Customer Reviews)
Make up for the height difference between your RV and towed vehicle with this hitch adapter. Provides either a 4" drop or a 4" rise for high or low ground clearance. Hollow shank is lightweight.by: Christopher01/29/2019
The tow bar rise extension was exactly what I needed to raise up the attachment point for my Roadmaster Falcon All-Terrain tow bar when pulling my Jeep Wrangler. Perfect fit and finish.
by: Lenny P02/14/2024
Good quality, perfect fit, didn't have to modify anything!
by: Bennie B.10/22/2012
Just as advertised. New tow vehicle is higher than the original tow vehicle, therefore required a riser to tow properly. This fit my needs. eTrailer provided excellent help and shipping was prompt. I am a repeat customer and will purchase other items when other needs arise.
by: Greg f08/24/2016
Item worked great on my JK Wrangler to connect my Thule bike rack. Customer service was top notch!!!
by: Randy S11/07/2013
Quality construction and it lowers the reciever to the correct height for my tow car. I would recomend this product.
by: Thad K.03/28/2011
I bought this in order to extend and lower a Thule T2 bike rack away from the spare tire on the back of a Jeep Wrangler.
The stock hitch mount location left the bike rack in the way of the spare tire when trying to fold the rack into the up position - and when lowering the rack to gain access to the rear of the vehicle.
This hitch extension gave me the perfect amount of clearance to implement all of the rack's operating positions. It's extremely well-made and super-duty. It's probably overkill for what I'm using it for, but I wanted the peace of mind that my rack and bikes were riding extra safely.
I was a bit worried that lowering the hitch would give me ground clearance issues, but those fears were unfounded. I still have plenty of room under there, and I can cross steep rail crossings without anything dragging.
For added peace of mind, I also ordered the anti-rattle lock (part #63232) and the quiet hitch (part # RM-061). The anti-rattle lock keeps this extension from being stolen. It also eliminates any side to side movement the extension has in the hitch.
The anti-rattle lock cuts down on almost all movement of the extension in the hitch; however, there was still a small amount of up and down movement. With the combination of the lock and the quiet hitch, the connection feels like it's welded on. If I was strong enough, I could lift the entire Jeep off the ground with this thing!
I'm really satisfied with the setup.
Jeff
8/19/2015
Thad,I recently got the 6 for my 2015 Wrangler, same reasons as you mentioned.Not knowing anything about TW, I didnt consider this in the purchase maximum 100 Lb. The Thule T2 is a pretty hefty rack and with 2 Mountain bikes on it, I would say its around 80-100 Lbs.Have you had any problems?When I sent in my review is when they cautioned me.
Tk
8/19/2015
Jeff, I have had zero issues with this extension or the Thule T2. My friends and I ride fat bikes. If youre familiar with them, theyre quite a bit heavier than a regular mountain bike. Ive had two fat bikes on that rack setup on many occasions. No problem.
Rachael H.
8/20/2015
Thanks for your follow up, but I would like to remind you that you will want to make sure that with your bikes loaded you will want to be within the tongue weight capacities of this high low adapter. Jeff, the Roadmaster High-Low adapters come in 2 different tonge weight capacities, you might consider the higher option that allows up to 400 pounds of tongue weight. These higher tounge weight capacity adapters have a solid shank which gives it the higher capacity, and the option with the same 4 inch drop would be RM-048-4.
Helpful Links
by: Kelly G09/17/2017
The offset hitch is everything that it was advertised to be. I am offsetting my hitch up and around the bumper on my motor home. The extra long 4" offset hitch worked perfect. Now the hitch is level with the tow bar on my Jeep. The delivery was fast and customer service was friendly.
Kelly G.
9/17/2018
I am very satisfied with the products I have purchased from etrailer. They are performing like new. I am especially pleased with the etrailer customer service and follow-up. Your business should always have success with that good attitude towards customer satisfaction.
by: DB05/15/2017
Item as described, works perfectly. Discovered I was going to be gone from home after I'd ordered this - talked to etrailer before it had actually shipped - they were able to re-route it to my destination, which is where I was needing it!
Db
5/15/2018
The products continue to perform well. Thanks for the follow up!
by: MarkJ11/30/2016
Needed to raise the blue ox tow bar on the RV to match the height of a new Wrangler JKU. This did the job perfectly without being too expensive.
Markj
11/30/2017
Still a 5 star in my book - does great.
by: Thomas 01/24/2020
Needed to drop the tow bar to match the new vehicle level for better tow control.
Every thing we use is Roadmaster it works the best.
Thomas G.
1/24/2021
Not as many trips due to COVID but have pulled the tow car around for about 4000 miles and it works perfect.
by: Dave01/10/2020
Had ordered a different hitch riser that wouldn't work because of the bumper on the motorhome, returned it and ordered one that Lindy A suggested. It just arrived about an hour ago , l put it on and everything is good.
Thanks so much for your help, never seem to go wrong dealing with you guys,
Thanks again
Dave
Dave B.
1/11/2021
It was good, since then we have changed motorhomes and cant use this one anymore, not tall enough, but when we used it, it performed as expected
by: Bill B06/17/2020
Purchased this to tow my Jeep behind my motorhome. Need the drop to properly align the towbar. Shortly afterwards, I lifted the Jeep and changed the front bumper. This unit was no longer needed. Only used it maybe twice.
With that said, it appears well made. Very strong and capable.
Only suggestion. I would like it to have more than one pin hole so it can be set farther into the receiver.
by: Craig C04/18/2015
Just what I needed to level my towbar . Ordering was easy and shipping is fast . I always use etrailer
Craig C.
4/17/2016
No problem . Perfect match for towing my toad
by: Ron01/20/2014
My Class B+ needed a rise of 4" to be within the 3" out of level spec for my Ranger. It does it's job--however it also moves my Roadmaster All Terrain towbar back about 11". The towbar sticks out back a lot and I was concerned the car behind me might hit it without a towed being hooked up. It may affect the "tail wagging the dog" a bit when the Ranger is in a rut and the RV isn't. I could shorten that distance by drilling new pin holes, but Roadmaster said NO!
by: Joe L03/20/2015
This product worked perfectly for towing my Corolla behind my RV using the Blue Ox
This worked perfectly for towing my Corolla behind the RV using the Blue Ox Alpha tow bar. There were no problems with hole alignments.
by: Ken C11/29/2016
Just received and installed. Untested, however. A bit of wobble noted between the stinger and receiver hitch interior Looks like a well built item and will allow me to bring my tow bar into the + or - 3" from level as per Roadmaster specs. Shipping was quite fast, even arrived a day earlier than promised w/o excuses as to conflicting with Thanksgiving holiday and/or black Friday, et al. Contact person at etrailer, George, was right on top of things and communicated via email which was much appreciated so I didn't have to guess about when shipped, etc. I really like these etrailer guys, my third purchase and it won't be my last. Oh yeah, no sales tax for us in California.
by: Larry 05/14/2020
etrailer was recommended to me by another RV'er. After talking with Paula S I can fully understand why the company was recommended. She was very helpful and knowledgeable concerning my questions. The product I ordered, a high/low hitch receiver for my motor home, arrived promptly and was exactly what I needed.
It appears customer service is a big priority to them. Highly recommend.
by: Richie B06/23/2017
Have a lifted jeep wrangler and need to raise the hitch to keep the tow bar level. This is the perfect hitch for my needs. The offset on the hitch helped me clear the bumper on my RV as my receiver is set-back under the bumper. Would recommend this product for Nemar RV owners that need to raise their hitch.
by: Earl M09/04/2018
Purchased items were delivered as promised and received in good condition. All worked perfectly as needed. After wiring a car to be pulled by a motor home, I found out a converter and two additional diodes were needed to make the lights function as needed. All are now installed and am very pleased with the outcome. Will have no problem with my next purchase ordering from etrailer.
by: Vittorio P08/05/2019
once again etrailer pulls through. the knowledge and experience (kirsten) and phone conversaton will bring me back again thanks ( big shout out)
by: Charles02/08/2018
Great service. Even called me before filling my order to make sure I had ordered the correct parts. Will be using them again. Thanks
Charles
2/8/2019
Ry good
by: Gary R06/10/2017
The RoadMaster drop down hitch would simply not fit my towbar. The towbar was not unique in the 2” hitch fitting as I confirmed with BlueOx and it fit the hitch on my RV just fine. The Roadmaster drop down hitch would fit my RV 2” hitch fine but the side for the towbar just would not budge. Once eTrailer Customer Service understood the issue they promptly sent me a pre-paid return label and provided a full refund. I believe the issue was a manufacturer defect. Very impressed with etrailer Customer Service and extremely happy with the return and refund process! Outstanding Customer Service and I would definitely buy from them again in the future.
by: RRichard M06/18/2016
Drop down adapter allows tow bar when towing car behind the motorhome to remain as same height as the hitch on the motorhome.
by: Carl V.07/08/2017
I needed this to ensure that the tow bar was within the specified +/- 3" height delta that Blue Ox recommends for their tow bar setups. The welds are solid and the finish is good.
25
182
Show More Reviews
See what our Experts say about this Roadmaster Accessories and Parts
- Cargo Carrier With Rise Shank Recommendation for a 2014 Toyota Sienna and Curt HitchThe best solution I can recommend for you would be to get a cargo carrier with a rise built into the shank so that it would sit high enough so that it wouldn't drag. The # RM-070 that you referenced has only been tested for use in flat towing setups. If you used it with a cargo carrier you would void the warranty. We have 3 carriers with build in shank rise. The enclosed carrier # M2205 has 5-1/2" rise, the open carrier # 63153 has a 2-1\2" rise and the # e98874 has a 2" rise. I...
view full answer... - Roadmaster Parts Needed to Flat Tow 2019 Ram 1500 New Body StyleWe do carry all the parts to give your 2019 Ram 1500 with the new body style a complete flat towing set up consisting of all Roadmaster parts. Please note the correct base plate kit will depend on if your '19 Ram 1500 is a Rebel model or not. Here are all the parts you'll need for your truck: - Base Plate Kit (2019 Ram 1500 All Models EXCEPT Rebel): Roadmaster Direct-Connect Base Plate Kit # RM-522203-5 OR - Base Plate Kit (2019 Ram 1500 Rebel Model Only): Roadmaster Direct-Connect Base...
view full answer...
- High-Low Adapter to Tow a Mini Cooper Behind a Motor HomeMost tow bars have a certain range in which they can work. That range is usually 3 inches off from level. A 6 inch drop would get you as close to level as you are going to get which is great. There is a chance that because the base plate connections on the Mini are so low that you could end up making contact with the ground and the adapter on uneven terrain or steep grades but for the most part in everyday towing situations it would not be a problem. What you could do is use an adapter...
view full answer... - 2007 Lincoln Navagater to carry a power chair on carrier about 420 LbsYou are correct. The RoadMaster 4 Inch Hi-Lo Drop, part # RM-070 is meant for use with a tow bar used for towing a vehicle. It is meant to tow a rolling load, not a situation where more than 100 lbs of downward force is applied to it.
view full answer... - Which High/Low Adapter for Flat Towing Lifted JeepYou'll need a high/low adapter to bring the tow bar within 3 inches +/- of level. The adapter you need will depend on the height difference between the base plates and the receiver on the motorhome/tow vehicle. Roadmaster offers several different adapters: • For a 2 inch rise/drop, use # RM-072-2 • For a 4 inch rise/drop, use # RM-070 • For a 6 inch rise/drop, use # RM-048-6 • For a 8 inch rise/drop, use # RM-048-8 • For a 10-1/4 inch rise/drop, use # RM-048-10 I've linked to an article...
view full answer... - Ball Mount For A Trailer That Has 4 Of RiseSince high-low adapters, like the Roadmaster High-Low Adapter for Tow Bars # RM-070 cannot be used to tow a trailer, I recommend getting a different ball mount to compensate for the needed 4" of rise. You can use the Curt Ball Mount for 2" Hitches # D-28, which offers 4" of rise, and 6" of drop, measures 14-1/4" long, and has a maximum weight capacity of 6,000-lbs.
view full answer... - Can Roadmaster High Low Adapter with Lower Capacity that Tow Bar Be Used SafelyAs long as the tow bar and high-low adapter are rated for at least the weight of the vehicle you are flat towing you'd be fine with one being rated for less weight. So if the 4 inch high-low adapter part # RM-070 will allow your to tow your Colorado level and the vehicle weighs less than 6,000 lbs this would be a great solution that would be perfectly safe. From what I was able to find your Colorado would weigh at most 4,520 lbs so you'd be fine.
view full answer... - Hitch and Ball Mount Recommendation for a 2008 Nissan RogueFor your 2008 Nissan Rogue I would recommend a Class III hitch like the Draw Tite Hitch part # 75902 as it would have plenty of capacity for towing your trailer and would give you greater flexibility for future hitch accessories like bike racks or cargo carriers. Since you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes...
view full answer... - Which Tow Bar is Compatible with Roadmaster EZ-5 Base Plates for 2020 Jeep Wrangler Unlimited The Roadmaster part you've referenced with part number 521450-5 is no longer available, but it was an EZ-5 base plate so I recommend using the Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar w/ LED Lights - RV Mount - 8K # RM-676, which comes with safety cables integrated into the setup. This would be compatible with the discontinued 521450-5 base plate you've mentioned or the current model, which is the Roadmaster Direct-Connect Base Plate Kit - Removable Arms # RM-521453-5. If...
view full answer... - Do Snow Plow Mounts on 2018 Chevy Silverado 1500 Need to be Removed to Add Base PlatesIn order to flat tow your 2018 Chevy Silverado 1500 you will need to remove the snowplow mounts to install base plates, as plow mounts are not designed or tested to withstand flat towing. You can use your Roadmaster StowMaster Tow Bar # RM-501, though you will need the crossbar-style base plates from Roadmaster with this tow bar. Along with the base plates, here are the other parts you'll need to flat tow your 2018 Chevy Silverado 1500: - Base Plate Kit: Roadmaster Crossbar-Style Base...
view full answer... - Recommended Adapter for Ground Clearance of Bike RackThe Curt Dual 2" Receiver Tube Adapter, 8" Extension # D-192 will work well to give you the extra height you desire but using any adapter will reduce your hitch tongue weight by 50%. This won't be an issue with a Curt Class III hitch is you just use your Ridgeback # Y02457. A similar option for more height is the Malone 2" Dual Purpose Hitch Receiver # MPG544 but it will also extend the length of the hitch 2-1/2 more inches than the # D-192. This will probably result in the adapter...
view full answer...
- Maximum Weight Capacity For a Cargo Carrier When Using an Adapter For Additional Ground ClearanceIf you are planning to use an adapter like the Roadmaster High-Low Adapter # RM-070 to raise a Cargo Carrier # C18110, the adapter will reduce the capacity of the receiver on your vehicle 50%. So if your receiver on your vehicle is rated for 500lbs of tongue weight it would be reduced by 50%, but the adapter itself has a maximum tongue weight capacity of 200lbs. So with the Cargo Carrier # C18110 weight of 30lbs that will limit you to 170lbs of cargo on the carrier. The Roadmaster High-Low...
view full answer... - Does Battery Need to be Disconnected to Flat Tow 2016 GMC CanyonWhen it comes to flat towing your 2016 GMC Canyon, you do have to disconnect the battery. We have to abide by what the owner's manual says, which is to ensure the steering column is unlocked and to keep the ignition key in the ACC (accessory) position. We don't have any way of knowing what might happen if you remove the steering lock and cannot recommend it. For specific instructions on this you can refer to your owner's manual; it was on page 327 of the online manual I took a look at. In...
view full answer...
- Availability of Hitch Adapter With a 4 Inch Rise That Will Fit a Thule Bike RackYou can use the Curt Multipurpose Ball Mount, part # D210, with a Thule bike rack that fits a 2 inch receiver. The ball mount receiver has a high enough tongue weight capacity at 350 pounds to handle the weight of the rack plus the bikes, and the drawbar has a total tongue weight capacity of 750 pounds. It will provide a rise of 4-3/4 inches above the top of the receiver opening on the hitch. It will help with bottoming out on vehicles that have low ground clearance.
view full answer... - Base Plate Adapters for 2020 Jeep Gladiator With ARB BumperThere are adapters which will attach to the D-ring bumper mounts on your 2020 Jeep Gladiator with an ARB bumper, though I was unable to find the exact size of the D-rings of your bumper. I recommend the Roadmaster option, and you simply need to take a couple quick measurements to determine the right adapter to flat tow with. Also keep in mind the mounting holes need to have a 7/8" or 1" diameter. - 3/4" Thick Shackle Mounts: Adapter for Jeep D-Ring Bumper Mounts - 3/4" Thick # RM-035 -...
view full answer... - Parts Needed to Flat Tow 2013 Toyota Yaris Hatchback With Manual TransmissionThere are a number of parts needed in order to flat tow your 2013 Toyota Yaris 2-door hatchback (sometimes referred to as a 3-door) with a manual transmission; I will list the parts for you below and all prices can be found on the respective product pages. - Base Plate Kit: Roadmaster EZ Base Plate Kit # 521181-5 - Tow Bar: Roadmaster Falcon All Terrain, Non-Binding Tow Bar # RM-522 - Safety Chains: RoadMaster 68" Single Hook, Coiled Safety Cables # RM-643 - Wiring Kit: Roadmaster Diode...
view full answer...
- How Much Length Will the RoadMaster High-Low Drop # RM-070 Add to Flat Towing SetupThe RoadMaster High-Low Drop # RM-070 would extend your tow bar out about an additional 10 inches. If you don't need the additional drop of 4 inches then this adapter wouldn't be needed as it is not a requirement for flat towing a vehicle. If you did need it the additional length wouldn't be too big of a deal. When you are already flat towing a vehicle behind your RV what's another 10 inches? I attached a picture that shows this adapter being used to flat tow a Mazda Miata.
view full answer...
- Will Roadmaster High-Low Adapter # RM-070 Work with Falcon All-Terrain Tow Bar and Tow DefenderThe Roadmaster High-Low Adapter, part # RM-070, is designed for use with a tow bar only. It will work with the Roadmaster Falcon All-Terrain Tow Bar, part # RM-522, you have referenced. This adapter is meant to be used when towing a rolling load on four wheels so it will not encounter any tongue weight or downward force of over 100 lbs. The tongue weight you will have on the adapter when towing a vehicle with the four wheels down will mainly be the weight of the stinger that is inserted...
view full answer... - Parts Needed to Flat Tow 2014 Honda CR-VWe can get you all the parts you need to flat tow your 2014 Honda CR-V, and let's start with the base plates you mentioned, which are a fit so long as your CR-V does not have the extra bumper trim package - the Roadmaster Direct-Connect Base Plate Kit # RM-521567-5. Keep in mind when installing this you will need the Loctite Threadlocker # LT37420. The best tow bar available, due to its long arms, lighting, and included safety chains - saving you an extra purchase - is the one you were...
view full answer... - What Tow Bars Work Well With Roadmaster EZ4 Base PlatesMost tow bars, especially those by Roadmaster, will work with the EZ4 Base Plate Kit with Removable Arms, Item # RM-521448-4. One of our popular tow bars that is made in the USA is the Roadmaster Sterling All Terrain Tow Bar, Item # RM-576. It is lightweight, durable, and easy to use and store. It also includes safety cables and works with 2 inch trailer hitch receivers. While you may already have them, you will also need tow bar wiring and a supplemental braking system for flat towing...
view full answer... - Does Roadmaster Nighthawk Tow Bar Work With Roadmaster EZ5 Base Plates on 2020 Chevy Silverado 1500The two parts you mentioned are absolutely compatible - the Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar with LED Lights # RM-676 will work superbly with the Roadmaster Direct-Connect Base Plate Kit # RM-523199-5 that fits your 2020 Chevy Silverado 1500. The Nighthawk tow bar will attach directly to the arms of the EZ5 base plates on your Silverado 1500 without any type of adapter or other part needed. You have made really good choices for your truck, because the EZ5 base plates...
view full answer... - Parts Needed to Flat Tow 2017 Ford Explorer With Roadmaster Falcon 2 Tow BarOk, so there are a number of parts you will need in order to set up your 2017 Ford Explorer with a 3.5L engine to flat tow with your Roadmaster Falcon 2 Tow Bar # RM-520. The first thing you will need are base plates, and I recommend going with the Roadmaster direct connect base plates for the easiest connection as well as the cleanest look for your '17 Explorer. The correct fit for these is going to depend on if your Explorer has Active Air Shutters or Adaptive Cruise Control; if it has...
view full answer... - Parts Needed to Flat Tow 2017 Jeep Wrangler JK Unlimited With Roadmaster Falcon 2 Tow BarThere are a bunch of parts needed to flat tow your 2017 Jeep Wrangler JK Unlimited so I can understand it can get a little confusing, but I'll make a list for you of the parts that you need to tow it with your Roadmaster Falcon 2 Tow Bar # RM-520. I will assume you have the standard factory bumper on your '17 Wrangler JK Unlimited, as you did not specify otherwise: - Base Plate Kit: Roadmaster Direct-Connect Base Plate Kit # RM-521448-5 - Safety Chains: Roadmaster 68" Single Hook, Coiled...
view full answer...
- Need Cargo Carrier That Sits Far Enough Away From Dual Exhaust on 2013 Jeep Grand CherokeeI recommend taking a look at the 24x60 etrailer Cargo Carrier, # 398874. This carrier has a shank rise of 2-1-2 inches and the closest edge of the carrier will sit 19-1/2 inches from the bumper of your 2013 Jeep Grand Cherokee. If you feel that this carrier will still sit too close to the dual exhaust on your Cherokee, you could use the Curt Dual 2 inch Receiver Tube Adapter, # D-192, which will raise the carrier 5-1/4 inches and push it 8 inches further away from the vehicle. Please...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Video by:
Joshua S
Test Fit:
Nicholas E
Test Fit:
Robert C
Video Edited:
Jacob T
Video Edited:
Chris R
Updated by:
Adele M
Updated by:
Wilson B
Updated by:
Amanda M
Updated by:
Isabelle B
Installed by:
Cole B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Christopher
2/4/2020
The riser is working great. I did add two hitch quietner U-bolts to keep the angle appropriate and to keep the connections from rattling. It is a great setup and I am super pleased with it.