Customers compare F02-2023 to these similar products
Products Featured in this Video
Today we're going to be taking a look at the Valterra 90 degree drain hose coupler. This coupler can let you connect 2 separate sewer hoses together or you can connect 1 hose and then connect the other end to a dump station. This is going to fit all 3 inch sewer hoses and 3 inch fittings. It's made from a durable black plastic construction. You can see it's the straight fitting. There's no… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
No they will all mount differently. For example, LaSalle Bristol Cable-Actuated RV Waste Valve - Black Water Tank - Spigot to Spigot - 96" Cable, part #34466N4BB96GM, needs ABS solvent cement, part #3447530889, to secure the valve to your sewer…
view full answer...To make your life easier you could just remove the center section of your current waste valve and then install just the center section of the part #E40B-8 so that you can convert to an electric setup without having to deal with a much more involved…
view full answer...Yes, the Valterra EZ Valve Electric Waste Valve for RV Black Water Tank #E40B-8 can be oriented sideways so it's able to open up under your trailer. The 3" to 3" hubs mentioned in the description are included with the valve. These are…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…
view full answer...Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…
view full answer...Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…
view full answer...A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…
view full answer...It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…
view full answer...If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…
view full answer...The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…
view full answer...