Can Center Section of Electric Waste Valve E40B-8 Replace Manual Setup

Question

Question:

Do I need to cut the existing hub off and replace both in and out hubs? Or can I remove the 4 bolts, slide out manual valve and slide in the electric valve??? To try and cut off existing flanges and glue on new to my 3inch pipes would be a major replumbing job which is not worth the upgrade.

asked by: Bruce W

0

Expert Reply:

To make your life easier you could just remove the center section of your current waste valve and then install just the center section of the part # E40B-8 so that you can convert to an electric setup without having to deal with a much more involved install since the pipes are plastic welded and can't come apart without cutting.

expert reply by: Jameson C

0

Answer 1

Yes, the Valterra EZ Valve Electric Waste Valve for RV Black Water Tank #E40B-8 can be oriented sideways so it's able to open up under your trailer. The 3" to 3" hubs mentioned in the description are included with the valve.…

view full answer...

Answer 2

The difference between a hub connection and a spigot connection is that the hub is the female end and has a lip on the inside that stops the spigot (or male) end where it needs to be. I have attached some pictures to assist. With this knowledge it…

view full answer...

Answer 3

The Valterra EZ Valve Electric Waste Valve for RV Black Water Tank item #E40B-8 may benefit from being installed up in your enclosed underbelly with the Valterra ABS Solvent Cement item #A05-0303 to help prevent the sewer pipes from freezing if you…

view full answer...

Answer 4

Yes you are correct Valterra EZ Valve Electric Waste Valve for RV Black Water Tank part #E1003VP does come with everything you will need. The confusion came from the spigot or hub ends and which one they needed for their application in that…

view full answer...

Answer 5

I spoke with Valterra and they stated that there's a microswitch inside of the Valterra EZ Valve Electric Waste Valve #E40B-8 that isn't sensing that the gate is fully closing causing the fuse to blow. This could be either an…

view full answer...

Answer 6

Yes, the MORryde Suspension Upgrade Kit #MR46ZR can certainly be used with the Lippert Road Armor Equalizers. You will just want to be sure that the stock shackle links on your 2021 Cougar 29RKS are 2-1/4" long when measured center hole to…

view full answer...

Answer 7

The distance from the top of the mounting plate to the bottom of the housing on the Bulldog Powered-Drive Trailer Jack, #BD500200, is 13 inches.

view full answer...

Answer 8

There unfortunately isn't a guide to tell us the equalizer, shackle straps, and leaf spring sizing for your 2016 Grand Design Reflection 313RLTS so you'll need to a bit a of measuring to determine the best replacements. Before measuring…

view full answer...

Answer 9

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 10

Hey Gene, we don't have that exact one you're looking for but we do have the Vitrifrigo C85i RV Mini Fridge with Built-In Freezer #VT34FR which is 3.2 cubic feet, runs off of 12V power, and does include a built in freezer.

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Can Center Section of Electric Waste Valve E40B-8 Replace Manual Setup

Product Page this Question was Asked From

Continue Researching