Customers compare MBS24FR to these similar products
Products Featured in this Video
Hello everybody, this is Jeff at etrailer.com. Today, we're gonna take a look at the 144 inch long three eighths inch thermal plastic high pressure hose with the three eighths inch female flare swivel ends on it. Now, this is a three eighths inch internal diameter general purpose hose assembly and it's used for LP and natural gas connections. The length we mentioned on this is 144 inches, has on… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
If you try to use two regulators you will most likely have too low of pressure you run your propane accessories. We had a customer come back who tried to use a RV gas grill that was regulated from a propane source that was already regulated and the…
view full answer...Here's what you need to do. On the 4 port adapter there is a very small plug with the tether on it going into a larger adapter with the other end of the tether on it that goes directly into the barrel of the 4 port adapter. Remove the small plug,…
view full answer...Fitting #CAM59953 is designed to connect a 1/4 inch inverted flare to a 1/4 inch female NPT. The one end is a 1/4 inch male NPT and the other is a 1/4 inch female inverted flare fitting. It sounds like you need one that does the opposite but we do…
view full answer...Yes, you will want to use some sort of thread sealer like part #LT37482 or pipe tape like part #A05-0265 on the NPT fittings inside of the MB Sturgis Single Stage Propane Regulator part #108072. As a general rule, all NPT fittings should have some…
view full answer...As long as your 80-lb propane tank uses a POL connection, then yes the Propane Adapter Fitting #37207-30125 with the MB Sturgis Propane Extension Hose - Dual Type 1 Tank Valve #100914-120-MBS will work great with your Weber propane gas grill.…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…
view full answer...I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…
view full answer...If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…
view full answer...Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…
view full answer...