Expert Review Video:
Multiplexed wiring with combined circuits. Stop, turn and tail light functions are sent along the same wire on each side of the vehicle. A powered converter module is required to safeguard the vehicle's wiring, decipher the signals, and better support the trailer lights.
Custom Fit Vehicle Wiring Specs:
Features:
Install a 4-way flat on your vehicle with this splice-in harness. Powered converter connects directly to battery to reduce strain on wiring. Potted, SMT construction boosts water and vibration resistance. Works with 2-wire, 3-wire, and PWM systems.
More Information >Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.
Tech Tip:
You will need to verify the type of plug by looking to see if you have a round plug or a rectangular plug to determine if kit will fit your vehicle.
More Information >Features:
Use your Stealth Hitches rack receiver to tow a small trailer with this all-inclusive towing kit. Remove the receiver attachment from your hitch and insert the included ball mount. Custom-fit 4-way harness, hitch ball and safety chain loops included.
Tech Tip:
This kit is designed to work with the vehicle specific Stealth Hitch trailer hitch.
More Information >Features:
Use your Stealth Hitches rack receiver to tow a small trailer with this all-inclusive towing kit. Remove the receiver attachment from your hitch and insert the included ball mount. Custom-fit 4-way harness, hitch ball and safety chain loops included.
Tech Tip:
This kit is designed to work with the vehicle specific Stealth Hitch trailer hitch.
More Information >Videos
for Custom Fit Vehicle Wiring
Help Articles
for Custom Fit Vehicle Wiring
Expert Answers
for Custom Fit Vehicle Wiring
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
view full answer...I&…
view full answer...If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly -…
view full answer...Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
view full answer...Filter Products (8)
Contact and Help
What our customers are saying:
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Kevin
Manchester, MD