Recommended Spare Tire Cover for 5.30-12 Spare Tire with a 21-3/4 Inch Diameter

Question

Question:

Will this cover fit on a 5.30-12 spare tire? Based on your FAQ on tire sizing my spare would be 21.752inch in diameter a bit larger than the 21inch that the cover is rated to. Thanks

asked by: N. C

0

Expert Reply:

The CE Smith # CE27410 spare tire cover you mentioned is designed to fit tires up to 21 inches in diameter. A tire that is about 3/4 of an inch larger in diameter than that would make for an extremely tight fit. Because the cover's made of vinyl, there will be some give to the cover, which might allow it to get around the tire, but I'd be worried about the vinyl tearing.

I believe the Classic Accessories # 052963751000 would be a better option, as it's meant to fit tires between 21 and 22 inches in diameter so it would be a much better fit.

expert reply by: Mike L

0

Answer 1

The diameter of your trailer tire size 5.30-12 is 21.3 inches so for a tire cover that will fit nice and snug I'd recommend the CE Smith cover part #CE27410 that you referenced as it is will fit your tire more snug than the other options…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 9

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Recommended Spare Tire Cover for 5.30-12 Spare Tire with a 21-3/4 Inch Diameter

Product Page this Question was Asked From

Continue Researching