Center Hole of U-Bolt Plate Isn't Large Enough Troubleshooting
Question:
My 1 1/2inch square axle will sit on top of my leaf springs, so the U-bolt plate will be on the bottom side of the leaf springs. There is a center hole on the U-bolt plate that should accept the protruding nut/bolt assembly that holds the leafs together as the U-bolts are tightened to the U-bolt plate. The center hole in the U-bolt plate is not quite large enough for the nut/bolt assembly and therefore, the U-bolt plate will not be flush to the leaf spring assembly. There is a chance then when I tighten the U-bolt nuts it will force the U-bolt plate flush to the leaf spring, but should I drill out the center hole in the U-bolt plate so that it easily fits over the nut, allowing the plate to be flush with the leaf spring? Thanks,
asked by: Jeff
Helpful Expert Reply:
If the center hole of your U-bolt plate isn't large enough for the nut on your leaf spring to fit flush you would want to drill it out large enough so that it will fit properly.
Product Page this Question was Asked From
U-Bolt Plate for 1-1/2" Square Trailer Axles with 1-3/4" Wide Springs
- Trailer Suspension Parts
- U-Bolt Plates
- Camper
- Car Hauler
- Utility Trailer
- 2000 lbs
- Square Axle - 1-1/2 Inch
- 1/2 Inch Diameter
- Redline
more information >
Continue Researching
- Video: etrailer Trailer Leaf Springs Review
- Search Results: 48 8 tire
- Video: Review of etrailer 2 Leaf Slipper Spring - e36SR
- Video: Redline Trailer Suspension 115983 Review
- Video: CE Smith Trailer Suspension - Leaf Spring Suspension - CE23102 Review
- Search Results: hubs for 1 inch spindle
- Q&A: Square U-Bolt Kit for Mounting Leaf Springs SP-177275 to 1-1/2 Inch Square Axle
- Q&A: Orientation of U-Bolt for Installing Leaf Springs on a Trailer
- Q&A: U-Bolts And Mounting Plates For A 1-1/2" Square Trailer Axle
- Shop: Karrier ST205/75R15 Radial Trailer Tire with 15" Silver Mod Wheel - 5 on 4-3/4 - Load Range C
- Shop: Kenda Karrier ST205/75R15 Radial Trailer Tire with 15" Black Mod Wheel - 5 on 4-1/2 - LR C
- Shop: CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
- Shop: Kenda 215/60-8 Bias Trailer Tire with 8" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: CE Smith U-Bolt Kit for Mounting 1-1/2" Square Trailer Axles - 3-3/8" Long U-Bolts - Zinc
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Shop: Trailer Hitch
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Article: Most Popular Wheel Bearings
- Search Results: 25580
- Shop: Trailer Wiring
- Q&A: Hub And Drum Replacement for 90865 Rockwell Hub and Drum
- Shop: Brake Controller
- Q&A: How to Determine if Trailer Axle is Not Aligned and How to Measure to Replace Trailer Axle
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Article: Trailer Tire Sizing
- Search Results: 68149
- Video: Choosing the Right Trailer Wiring