Bracket Dimensions for the CE Smith Side Angle Mounting Brackets # CE10211G

Question

Question:

CE Smith Side Angle Mounting Brackets for Boat Trailer Rollers - Galvanized Steel - 1 Pair CE Smith Boat Trailer Part Code: CE10211G Hi Can I have The dimensions of this bracket? Thanks

asked by: Gabriel

0

Expert Reply:

I went out into our warehouse and pulled a CE Smith Side Angle Mounting Brackets # CE10211G to get some measurements for you. Check out the picture I attached to see them all.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The CE Smith Side Angle Mounting Brackets for Boat Trailer Rollers - Galvanized Steel - 1 Pair #CE10211G have holes that are 2-1/4 inches on center and 1-1/4 inches on center in the other direction. I've attached a photo to assist as well as a…

view full answer...

Answer 2

From past customers we have found that the TeeNee trailers use a three inch keel roller like the part #YR300Y. That being said I would need to see a picture of your setup to give you the best options we have. I did some research on your Tee Nee…

view full answer...

Answer 3

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Bracket Dimensions for the CE Smith Side Angle Mounting Brackets # CE10211G

Product Page this Question was Asked From

Continue Researching