Installation Instructions for Curt Front Mount Trailer Hitch Receiver # 31084 on 1999 Jeep Cherokee

Question

Question:

Do you have installation instructions for Curt Front Hitch # 31084 for a 1999 Jeep Cherokee? I could not find a link for this. Thanks and God bless.

asked by: Duke

0

Expert Reply:

I have attached the installation instructions for the Curt Front Mount Trailer Hitch Receiver, # 31084, on a 1999 Jeep Cherokee. The link to the instructions is located on the right of this page.

expert reply by: Leah S

0

Answer 1

The air dam does need to be trimmed (or removed) to install front mount trailer hitch #65009. The skid shield, if present, would have to be removed. I have included a link to the installation instructions for this hitch so you can see the…

view full answer...

Answer 2

Sounds like you have a boat trailer that you tow your Triton 21RX with that has surge brakes that are locking up in reverse. This is a fairly common scenario that has an easy fix. With surge brakes, you have a brake actuator applying the needed…

view full answer...

Answer 3

I did some checking and all versions of the 2000 Jeep Cherokee 4x4 are flat towable without speed restrictions. The only specific step I was able to find was that whenever possible start the engine of the Cherokee and let it run for 5 minutes to…

view full answer...

Answer 4

The only difference between the Curt Trailer Hitch #13084 and the Curt Trailer Hitch #13160, is the shape of the tubing. Curt Trailer Hitch #13084 has a square-tube design while the Curt Hitch #13160 has a round-tube design. The square-tube hitch…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 9

If you have the Ford 3" hitch then you can definitely add it but, yes it would change the weight capacity. The TorkLift Cannon Hitch Extension item #TLE1636 only has a 3,600 lbs towing capacity and a 360 lbs maximum tongue weight. If used with a…

view full answer...

Answer 10

Yes that is correct, Eugene. Since the canister sits flush with the bed rails, you'd effectively have 9" under the canister.

view full answer...

Answer 11

The canister of the Pace Edwards UltraGroove Retractable Hard Tonneau Cover #PE57CV is 12" tall x 10-1/4" deep.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Installation Instructions for Curt Front Mount Trailer Hitch Receiver # 31084 on 1999 Jeep Cherokee

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching