Can the 2nd Motorhome Kit # RM-98850 Be Used on a Motorhome with 7-way and Towed Vehicle with 4-Way

Question

Question:

Can the wiring be connected to my seven pin plug on the rear of my MH? I only have a four pin plug on the towed vehicle. Or do I need to change the plug on the towed vehicle to make it work?

asked by: Gary A

0

Expert Reply:

All you would need is the correct adapter to go from the 7-way of your motorhome to the 4-way of your tow vehicle. For that I would recommend the Coiled Adapter part # 787196.

expert reply by: Jameson C

0

Answer 1

For the Invisibrake #RM-8700 we have a second motorhome kit with the part #RM-98850 which is the just monitor/alarm that installs in the motorhome like you need.

view full answer...

Answer 2

I would be happy to help! What you will need to do to get the Roadmaster 2nd Motorhome Kit #RM-98850 installed in your 2022 Mercedes-Benz is first install the LED light in your Sprinter where ever you decide is the best location that is visible while…

view full answer...

Answer 3

The motorhome monitor alarm in Monitor/Alarm Kit #RM-98850 will not sound when you press the motorhome brake pedal. If someone presses the toad brake pedal for more than 20-seconds then you should hear the alarm. As for the breakaway my contact at…

view full answer...

Answer 4

If you use the ground pin for all of the grounds from #RM-98850, #RM-98800, and #RM-155 then a 6-Way connector could handle the lighting, RV monitoring light, and one other function for a total of 6 functions (including the ground). The lights will…

view full answer...

Answer 5

When it comes to the procedure for a specific vehicle for flat towing you have to go with what the manufacturer recommends. Either by what's in the owners manual or by contacting the manufacturer of the vehicle. Based on what you listed you would…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 8

The first component you'll need to flat tow your 2023 Ford Bronco is a base plate kit like the part #RM79RR which connects to the vehicle frame to provide a connection to the tow bar. In addition to the base plates, you will also need a…

view full answer...

Answer 9

Here are the steps to prepare your 2023 Ford Bronco Big Bend for flat towing. The transfer case and transmission will be in neutral with the ignition off. This information is in your owners manual. Switching Neutral Tow On 1.Switch your vehicle to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

No, you can't. Those hooks are only for recovery or pulling something they're not rated to be flat towed with. You are actually going to have to remove them to install a base plate kit on your 2023 Ford Bronco. Since you have a Blue Ox Alpha…

view full answer...

Answer 12

The best base plate for your 2023 Ford Bronco is the Roadmaster Direct-Connect Base Plate Kit item #RM92ZR. You will need to use the Demco Tow Bar Adapter Kit item #DM9523032 to connect it to your Demco Dominator item #DM9511008. There is a Demco…

view full answer...