How to Route Wiring Through Firewall When Installing Brake Controller on 2014 Ford Escape
Question:
etbc7 and primusiq...for 2014 ford escape. any suggestions on how to get from engine compartment thru firewall to driver cab ?? I cannot find any openings and there is no room under hood.??????
asked by: Geoff B
Expert Reply:
Your best bet is always going to be using an existing opening. If you can find an existing grommet where a factory wiring harness passes through the firewall into the passenger cabin, you can use a sharp knife to carefully poke a slit in the rubber or plastic grommet to pass the wire through.
If you cannot find anything, you'll need to drill your own hole, being extremely careful to make sure that there's not anything on the other side of where you're drilling that would be damaged.
You can drill an 11/16 hole, and use a snap bushing grommet like # SWC8057. The grommet will protect the wires from the edges of the hole. Once your wiring is complete, use some silicone sealant like # LT37464 to seal around the wiring to prevent water or fumes from entering the passenger cabin.
Products Referenced in This Question
Loctite RTV 5699 High-Performance Silicone Gasket Maker - Grey - 2.7-Fl Oz Tube
- Lubricants Sealants Adhesives
- Sealant
- Gasket Maker
- 2.7 oz
- Loctite
more information >
Snap Bushing Grommet - 9/16" ID, 11/16" OD
- Wiring
- Wiring Protection
- Bushing Grommet
- 9/16 Inch Diameter
- Spectro
more information >
Product Page this Question was Asked From
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Trailer Hitch Installation - 2016 Ford Edge - Draw-Tite 75214
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Search Results: trailer hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Trailer Hitch Installation - 2016 Ford Edge - Draw-Tite
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Trailer Wiring Harness Installation - 2016 Ford Edge
- Video: etrailer Class III Trailer Hitch Installation - 2017 Ford Edge e36RR
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Does Power Wire have to be Run to Battery to Install Trailer Wiring Harness on 2015 Ford Edge Sport
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: etrailer Trailer Hitch RHK Review
- Article: How to Choose the Right Trailer Hitch Class
- Video: Curt Trailer Hitch Installation - 2016 Ford Edge C13234
- Video: Choosing the Right Trailer Wiring
- Search Results: hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Shop: Brake Controller
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Search Results: trailer hitch wiring
- Shop: Roof Rack
- Search Results: brake controller