What To Do if You Bend the Outer Tube of a Bulldog Powered-Drive Trailer Jack

Question

Question:

I bent the outer tube of my 3500 jack his last weekend. It will still extend and retract as it should but I need to replace the outer tube. Can I replace that part myself and could you help me find the parts?

asked by: Doug D

0

Expert Reply:

I wish I had something I could offer you, but I spoke with my contact at Bulldog and he informed me that the outer tube for this jack is not available. You will need to replace the entire jack.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 3

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 4

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 5

Hi Tom, I have two options to replace the electric tongue jack on your Jayco Whitehawk: Option 1: Electric Jack w/ Footplate #EJ-3520-BBX. This jack is going to be your no-frills 'get the job done' style jack. It has a 3,500lb capacity and…

view full answer...

Answer 6

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…

view full answer...

Answer 9

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 10

Hi Bruce, To lift your trailer we'll first need to check of the suspension and see if you have torsion axles or a leaf spring suspension. If you have torsion axles then I'll need to see the axle tag in order to determine what you have so I…

view full answer...

Answer 11

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

Answer 12

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately…

view full answer...

What To Do if You Bend the Outer Tube of a Bulldog Powered-Drive Trailer Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching