What Comes with the Yakima Replacement Spine Assembly

Question

Question:

Hi, what comes i the package? Does it come with a nut and bolt or screw? Thank you! locking pin

asked by: Niel A

0

Expert Reply:

What comes with the Yakima Replacement Spine Assembly part # 8890277 that you referenced is what you see in the product picture that I attached. You would need to reuse the installation hardware from your current rack to install this on your Yakima Holdup bike rack.

For a hitch bolt you would want the part # Y8890200. For a lock for the bolt you would want part # Y07235.

This spine is designed to fit the older generation of the HoldUp manufactured through late 2012. If you have the newer Holdup you would want the part # .

expert reply by: Jameson C

0

click to enlarge

Answer 1

I do not see why you could not take the trays from the Plus 2 and attach them to this spine to get a complete 2 bike rack. I spoke with my Yakima contact and she said you should be able to do it, but if you want to make it a true Hold Up, you will…

view full answer...

Answer 2

The Replacement Spine for Yakima HoldUp Bike Rack #8890277 does come with the threaded insert that the hitch pin would thread into.

view full answer...

Answer 3

When replacing the spine for the Yakima Hold Up The Replacement Spine for Yakima Plus 2 2-Bike Add-On for Yakima HoldUp #Y8890279 will work for the 2 bike add on. If you are looking for just the original spine for the Yakima HoldUp bike rack then you…

view full answer...

Answer 4

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 5

You will need the Yakima Replacement Spine Assembly for 2 inch HoldUp Bike Racks, item #8890277, to replace the shank on your 1-1/4 inch HoldUp rack and make it work correctly in your 2 inch hitch.

view full answer...

Answer 6

For your Yakima Hold Up, the Replacement Spine #8890277 will require the Replacement Hitch Hardware for Yakima HoldUp Bike Racks #8890260. The 1-1/4 inch hardware will not be the correct fit for the larger shank.

view full answer...

Answer 7

The Yakima Holdup Bike Racks regardless of generation all use the Hitch Bolt part #Y8890200. It's possible you stripped the nut so in which case you would just need the Replacement Nut Retainer and Nut part #Y90254.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...