Choosing the Right Dexter E-Z Flex Suspension for Replacing Standard Equalizers

Question

Question:

Wanting to put a Dexter ez flex tandem suspension kit on my boat trailer. I have heard that I might lose some wheel clearance on my fenders wondering what my options are since I cant raise my fenders, thanks.

asked by: Ross

0

Expert Reply:

You shouldn't loose any wheel clearance with the Dexter E-Z Flex Suspension Kit. First you will want to see which of the Equalizers you need. There is a 6,000lb Equalizers # K71-654-00 (5-5/8") and 8,000lb Equalizers # K71-655-00 (7-3/4"). The 6,000lb is for hubs spread 33" on center and 8,000lb for hubs 35" on center.

If you choose either the Dexter E-Z Flex Suspension 6,000lb Kit # K71-652-00 or 8,000lb Kit # K71-653-00 they will include 2-1/4" shackle straps. If your current shackle straps are shorter the kit will lower your suspension slightly. If your straps are longer it will raise your suspension slightly. If you need help finding the right size replacement straps please let me know what length you currently have.

expert reply by: Bud M

0

Answer 1

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 2

We actually reached out to Silent Ride about this and while they don't offer an all-in-one kit for triple axle setups, they did confirm that you can use three of the Single Axle kits like part #TSR7KS02 and it will work great. This particular set…

view full answer...

Answer 3

I reached out to Lets Go Aero for confirmation that you can even use the Demco 50-Degree A-Frame Coupler #DM15349-52 and they said that you will not have any structural issues with having the bolt holes drilled in the sides of your Frame as the Demco…

view full answer...

Answer 4

Your pictures didn't make it through, but if your equalizers look bad it would be a good idea to replace them. Now chucking is typically caused by the jaws of the fifth wheel hitch being used. Some hitch designs are just more prone to movement…

view full answer...

Answer 5

The easiest way to accomplish this would be to start on one side of the trailer and get the springs in place before bolting the axle to the springs with the u-bolts. Have the axle up on jacks or blocks so its weight is not bearing on the springs.…

view full answer...

Answer 6

If your trailer has torsion axles, no worries but it it's a leaf spring suspension you really should have equalizers. Without the equalizer, the trailer will have a rougher ride and the weight won't be balanced across both axles when going…

view full answer...

Answer 7

Yes, dielectric grease like the Dielectric Grease for Electrical Connectors #11755 can and should absolutely be used on electrical connectors like your 4-pin trailer connector. Dielectric grease does a great job of protecting your equipment from…

view full answer...

Answer 8

Since your Grand Design 17MKE has a GVWR of 6,395 lbs, you more than likely have 3,500 lb axles. That being the case, the Roadmaster Comfort Ride Leaf Spring Suspension Kit #RM-2460-2560 will not fit your travel trailer. Although Roadmaster does not…

view full answer...

Answer 9

Trailer manufacturers don't usually keep a record of parts like these that they install at the factory, so I cannot be sure as to the exact length of the shackle strap that would have come originally on your trailer. With this in mind, a 3-1/8…

view full answer...

Answer 10

Based on the dimensions you mentioned the correct Dexter EZ Flex kit you would need is the part #K71-654-00 which is compatible with what you have and will do a great job improving ride quality.

view full answer...

Answer 11

The Lippert Components High-Speed Power Stabilizer Jack part #LC298707 is a stabilizer jack and is not designed to lift therefore, does not have a lift capacity. It will be suitable for most camper trailers, travel trailers, 5th wheel trailers, and…

view full answer...

Answer 12

The Replacement 5-5/8" Equalizers for E-Z Flex Heavy Duty Rubber Suspension System #K71-654-00 you referenced are simply replacements for the E-Z Flex Heavy Duty Rubber Suspension System by Dexter Axle - 5-5/8" Equalizers #K71-652-00. To…

view full answer...

Choosing the Right Dexter E-Z Flex Suspension for Replacing Standard Equalizers

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching