Diagram for Wiring the 2006 BMW X5 Trailer Wiring Harness

Question

Question:

Can you show me the wiring diagram for an 06 BMW X5

asked by: Daniel K

0

Expert Reply:

Yes, the wiring diagram for wiring the # 119250KIT wiring harness is in the instructions (see link). You will need to attach the wires from the converter on the harness by function only using the included circuit tester.

Your 2006 BMW X5 has a 3 wire Multiplexed wiring system that requires a different wiring configuration. Your vehicle has a combined stop and tail light circuit and an additional tail light wire. You will attach the red stop light wire to the combined circuit and the brown tail light wire to the independent tail light circuit.

You will then need to connect the yellow wire to the left side turn signal and the green wire the right side turn signal.

Finally you will need to attach the power wire to the vehicle battery through the included inline fuse to protect your vehicles sensitive wiring and circuitry.

expert reply by: Robert G

0

Answer 1

Thanks for reaching out! To add tail lights and a license plate to your Kuat NV 2.0 Bike Rack #NV22G I recommend picking up the Curt Auxiliary LED Indicator Lights #C53201 and the Thule License Plate Holder #TH35JV - you'll need to splice in the…

view full answer...

Answer 2

For the license plate, you have two options. You can use the Yakima PlateMate License Plate Holder for Bike Racks #Y02713. This uses a hook and loop strap to attach to your bikes or your rack and is quick, easy, and temporary. The downside to this…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Diagram for Wiring the 2006 BMW X5 Trailer Wiring Harness

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching