Class I Receiver Hitch for 2009 Ford Fusion

Question

Question:

Hi Im wondering about product number 24865 I was wondering if this will fit on a 2009 fusion.

asked by: John

0

Expert Reply:

The Draw-Tite Class I Receiver for your 2009 Ford Fusion is part # 24755. This hitch offers easy bolt-on installation.

The Draw-Tite Class I Receiver, # 24865, that you mentioned is manufactured to fit the 2010 thru 2012 Ford Fusions.

expert reply by: Leah S

0

Answer 1

There is a pretty significant difference when it comes to the hitches you mentioned that fit your 2018 Chevy Bolt EV, the Draw-Tite Trailer Hitch Receiver #24956 and EcoHitch Hidden Trailer Hitch Receiver #306-X7359. As you mentioned, the Draw-Tite…

view full answer...

Answer 2

You are probably OK but if you are anything like I am it would be too close for comfort. I wouldn't want to take a chance at potentially causing any damage to my fascia. I recommend the Curt Class II Drawbar - 5" Rise -…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" #C11048 is compatible with the Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs #C45015 you referenced. You will also need a hitch ball like #19256…

view full answer...

Answer 4

When we installed the Draw-Tite #24755 Class I hitch on a 2007 Acura TL, we found that the inside top edge of the receiver tube sat 10-1/2 inches above the pavement. To determine which ball mount would place your trailer as close to level as…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

Thank you for the photos and sorry to hear about your truck! The unique design of the B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate #BWTS20066BMP is that angled section that meets with the shank part of the ball mount. On…

view full answer...

Class I Receiver Hitch for 2009 Ford Fusion

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching