Where Will the Receiver be Once Curt Front Mount Trailer Hitch is Installed on 2008 Ford Ranger

Question

Question:

Was wondering if this lines up with the gap on the lower valance on a 2008

asked by: Ray

0

Expert Reply:

Installation of Curt front mount trailer hitch # C31063 will actually require some trimming of front fascia on a 2008 Ford Ranger. I have linked the instructions for you that show where the trimming takes place. This means it will likely be up higher than you think.

Please note, this hitch will not fit on models with a front cross-member. Hitch does not fit 2WD vehicles built in Canada.

expert reply by: Michael H

0

Answer 1

I spoke with my contact at Curt and he provided a picture to show what to look for when it comes to determining whether your 2000 Ford Ranger has the front crossmember. You will see his picture off to the right. If your Ranger DOES NOT have a…

view full answer...

Answer 2

According to our friends at Curt Manufacturing, Front Mounted Receiver Hitch, part #C31063 is a fit for your 2000 Ford Ranger 4X4. If the truck is equipped with a skid shield, it must be removed to install the hitch. It will NOT fit on models with a…

view full answer...

Answer 3

We have a front mount, 2 inch receiver that will fit your 1998 Mazda B-Series pickup truck. It is Curt hitch #C31063. The only exceptions are that it will not fit on models with a front cross-member or 2-wheel drive models that were built in Canada.

view full answer...

Answer 4

Sounds like you are referring to a trailer hitch. And no, not all vehicles come from the factory with trailer hitches installed so the one you are selling just may not have ever had one. To see what a trailer hitch looks like that would fit your…

view full answer...

Answer 5

Our hitch installers often find that on even fairly new trucks the weld nuts in the frame can becomes rusted enough (or filled with salt or dirt) that the hitch installation hardware does not want to thread properly. It can be an even worse problem…

view full answer...

Answer 6

I definitely have the installation instructions for the Curt Front Mount Hitch #C31063 for your 2006 Ford Ranger. I went ahead and attached the pages to this answer. I also confirmed with Curt that this hitch fits a 2006 Ford Ranger XLT 4x4. Toward…

view full answer...

Answer 7

There sure is! To order the replacement mounting hardware for the Curt Front Mount Trailer Hitch Receiver #C31063 you have you will need the Replacement Hardware Kit #RHK. You will need to select Curt from the drop down menu, and then enter 31063 as…

view full answer...

Answer 8

I was able to get some dimensions for you on the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" #C31063. The overall width is 31-1/8 inches. The mounting holes are 29 inches by 10 inches on center. The receiver tube is 8 inches total…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Where Will the Receiver be Once Curt Front Mount Trailer Hitch is Installed on 2008 Ford Ranger

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching