Recommended Brake Controller For A 2007 Monaco Dynasty

Question

Question:

I have a 2007 Monaco Dynasty On a Roadmaster chassis In need of a top of the line brake controller for my two axle trailer RV has engine brakes as well as air brakes. Thank you in advance! Dan

asked by: Danniel S

0

Expert Reply:

Hey Danniel,

If you don't already have a 7-way or 4-way on the back of your motorhome then you'll need to start with the Curt 4-Way Flat Trailer Connector with Circuit Protected Powered Tail Light Converter # C85FV. This will splice into your factory tail light wiring and run up to the battery for power. From there you can install the # ETBC7 7-way kit. This will plug into the 4-pole wire harness for the lights and have wires to run to power/ground and up to the brake controller.

Once all the wiring is in place you can start installing a brake controller like the Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness # RED52VR. This brake controller takes up the least amount of space on the dash compared to any other option and gives you a factory look. It will come with a splice in wire harness that needs to run to power/ground, the brake controller output wire from the # ETBC7 and to the cold side of the brake light switch.

You can find the cold side of the brake light switch by probing # PTW2993 the wires coming from the top of the brake pedal. You'll want to find the wire that only has power when the brake pedal is being depressed. If you can't find this wire then you can just install a stop light switch kit # RM-751000 to simulate this signal.

expert reply by: Kevin C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...

Answer 9

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 12

Hey Danniel, If you don't already have a 7-way or 4-way on the back of your motorhome then you'll need to start with the Curt 4-Way Flat Trailer Connector with Circuit Protected Powered Tail Light Converter #C85FV. This will splice into your…

view full answer...

Recommended Brake Controller For A 2007 Monaco Dynasty

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching