Solution for Connecting to Cold Side of Brake Switch on 2019 Subaru Outback

Question

Question:

I recently purchased the Tekonsha BRAKE-EVN Trailer Brake Controller - 1 to 4 Axles - Proportional and the ETBC7. I am unable to get to the brake switch cold wire to make a connection on my 2019 Outback. Is it OK to run a separate wire from the brake controller to the rear of car and splice into the brake wire on the optional four-way connector? Thanks for your help

asked by: John K

0

Expert Reply:

Hi John; I would not run a wire all the way back and try to connect it on your 4-way to install the # TK63VR. Instead, you can use the Roadmaster Universal Stop Light Switch Kit # RM-751000. The kit will become the new connection point for your red wire and you won't run any risk of overloading a circuit. This is often the solution for vehicles where you can't access the cold side of the brake switch.

expert reply by: Robin H

0

Answer 1

This is a great question. I called my contact at Progress Manufacturing (creator of Equalizer and FastWay Weight Distribution products) to pick his brain on this topic. He explained that weight distribution (WD) and sway control products rely on…

view full answer...

Answer 2

The cold side of a brake light switch is used as the trigger signal to activate a trailer brake controller like the Prodigy P2 #90885. The controller installation kit you purchased, part #ETBC7, includes a probe-style circuit tester that allows you…

view full answer...

Answer 3

For a complete towing setup for your 2010 Dodge Nitro Heat to pull your 21 foot travel trailer, you will need a hitch, brake controller, and wiring. In addition, I would recommend a weight distribution system with sway control, and adding an…

view full answer...

Answer 4

We have everything you'll need to install and wire up a brake controller and 7-way in your 2019 Subaru Outback Wagon. The easiest to install brake controller that also happens to be one of the best performing models is the Curt Echo part #C51180.…

view full answer...

Answer 5

The phrase "the cold side of the brake switch" refers to the circuit at the brake switch that carries voltage only when the vehicle brakes are applied. This circuit varies widely from vehicle to vehicle so the best way we can recommend you…

view full answer...

Answer 6

Yikes, the camper dealer you went to really didn't do you any favors by only installing your brake controller so that it can operated with the manual override lever. We can definitely help as the only safe way to tow with a brake controller is so…

view full answer...

Answer 7

When you are hardwiring a trailer brake controller like the Prodigy P2 #90885 the red wire connection that provides the triggering signal to the controller should be made to the wire on the COLD SIDE of the brake light switch circuit. This is the…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Solution for Connecting to Cold Side of Brake Switch on 2019 Subaru Outback

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching