Availability Of Dexter Bearing Kit K71-718-00

Question

Question:

Hi, I’m looking for Dexter part 1-3/8inch x 1-1/4inch 4,400 Lb. Trailer Axle Wheel Bearing Kit K71-718-00 , I am unable to find this on your site. Was wondering if it may be labeled as something else or just something you don’t carry

asked by: Jerimiah

0

Expert Reply:

Hey Jerimiah, so we have a solution, but we do not carry the exact Dexter Bearing Kit K71-718-00 that you are looking for as a single part number. We do carry all of the components of this kit individually though, and I have listed all of the components below:

- Grease Seal # RG06-050

- Cotter Pin # 165649

- Outer Race # LM67010

- Outer Bearing # LM67048

- Inner Race # L68111

- Inner Bearing # L68149

expert reply by: Jameson C

0

Answer 1

Yes, a Lippert 4,400LB torsion axle will use the same Bearing Kit #BK2-100 as their standard 4,400lb axle. This kit includes the following components if you only need to replace some of the components and not everything. Outer bearing #L44649 Inner…

view full answer...

Answer 2

Lippert 4,400 lb axles use the same bearings as 3,500 lb axles so the correct kit is the Hub Bearing Kit #BK2-100.

view full answer...

Answer 3

Lippert's 4,400 lb axles like what you have use the same bearings as 3,500 lb axles so the correct replacement bearing kit is the following: - Bearing Kit #BK2-100

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 7

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Availability Of Dexter Bearing Kit K71-718-00

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching