Bearing Kit that Fits Lippert 4,400 lb Trailer Axle

Question

Question:

I’m looking for a replacement seal and bearing kit for a Lippert torsion axle. The number on the axle is LCI35H-DTBSA-89.5-59.25-ID-22D-LP1B-L-655-18PT-CAP 4400 Do you have the correct part number for this axle?

asked by: Brian S

0

Expert Reply:

Lippert's 4,400 lb axles like what you have use the same bearings as 3,500 lb axles so the correct replacement bearing kit is the following:

- Bearing Kit # BK2-100

expert reply by: Jameson C

0

Answer 1

The 4,400 lb trailer axles use the same bearings and seals as 3,500 lb trailer axle so for this you can use the Bearing Kit for #84 Spindles part #BK2-100.

view full answer...

Answer 2

The Dexter 4,400 pound will need the same type of kit used for the 3,500 pound axle. You can find it here, Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles - 3,500 lb with #84 Spindle #BK2-100. I suggest getting some extra seals too because…

view full answer...

Answer 3

The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part #BK2-100 which comes with bearings, races, and seals. It looks like the 85 number you have found in your part…

view full answer...

Answer 4

We definitely have the replacements needed for your Lippert 4,400 pound axle. For the bearings, we do have what you need separately, but as this is a fairly uncommon size axle, we do not have an inclusive package. I have the inner and outer…

view full answer...

Answer 5

I have a set of leaf springs for your Lippert Axle they are 6-Leaf Double-Eye Spring for 4,500-lb Trailer Axles - 26" Long item #e27SR. You will want to measure the spacing on your mounting brackets to confirm compatibility. The length…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 9

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 10

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 11

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Bearing Kit that Fits Lippert 4,400 lb Trailer Axle

Product Page this Question was Asked From

Continue Researching