Replacement Landing Gear Motor for a 8532-07 Motor

Question

Question:

Hello, my landing gear motor just died on me and I cant lower and raise my 5th wheel. I got the P/N on the motor and its 8532-07. I cant find it anywhere. Can you guys help me find a replacement motor?

asked by: Johnny H

0

Expert Reply:

Hey Johnny, thanks for reaching out!

I highly recommend using the Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor # LC196308 as a replacement for your 8532-07 motor.

According to my research your motor is rated for 5,500 lbs so this motor will be able to handle the job easier, although it's important to note that this won't increase the lift capability of your landing gear itself.

expert reply by: Jon G

0

Johnny H.

5/11/2024

Hello, that one is a little pricey. I’m trying to replace my gear box also. Would this motor also work? LG-142178 and I was looking at this gear box LG-179015

Reply

Jon G.

5/13/2024

@JohnnyH You can use the Motor # LG-142178 and Gearbox # LG-179015 and it will physically fit, yes. Just know that this has a 5,500 lb weight rating compared to the 6,500 lb rating of the one I recommended.

Helpful Links

tv-demo-stromberg-carlson-accessories-and-parts-lg-142178.aspx

tv-demo-stromberg-carlson-accessories-and-parts-lg-179015.aspx

Reply

Answer 1

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw…

view full answer...

Answer 2

Any powered landing gear or powered tongue jack will draw less power as it legs descend down toward the ground and much more as soon as they make contact and encounter resistance. This is a normal occurrence. In the same way, any jack - even a manual…

view full answer...

Answer 3

Motor and Switch Kit for Stromberg Carlson Landing Gear - 5,500 lbs #LG-217884 only will use one switch. If you were to use two motors, then dual switches would be used. I've attached a diagram to assist. The input wires from the battery can be…

view full answer...

Answer 4

The correct replacement landing gear legs are the Lippert Replacement Lead Leg for Kestone Montana 5th Wheel #LC178653 and the Replacement Follow Leg #LC178652. You mentioned that you've already replaced the motor and switch, ##LC217884, and the…

view full answer...

Answer 5

From what I could find it looks like your ADTH 1RV-200 motor has a weight capacity of 6,500 lbs. You can use a motor that is rated for a higher capacity, like our replacement motor #LC142178 for Ram landing gear which is rated at 8,000 lbs. Just keep…

view full answer...

Answer 6

For your Venture landing gear you can use #LC276602 or #LG-179015. Either one will work.

view full answer...

Answer 7

The Stromberg Carlson Replacement Motor #LG-196308 and the Lippert HD Motor #LC196308 referenced in your question are essentially the same motor. They can be used interchangeably on a landing gear system. With this in mind, I simply recommend…

view full answer...

Answer 8

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 9

I reached out to my contact at Lippert and since your landing gear motor is blowing a fuse as soon as it sees load he mentioned the issue is more than likely that the motor is not getting the correct voltage, with the less common cause being the…

view full answer...

Answer 10

If it a jack isn't able to raise a trailer properly it's generally because it isn't getting enough power or there is hardware problem. I would first check the wiring and make sure there isn't a short. Also, inspect and clean the…

view full answer...

Answer 11

Hey Johnny, thanks for reaching out! I highly recommend using the Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 as a replacement for your 8532-07 motor. According to my research your motor is rated for 5,500 lbs so this motor will…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Landing Gear Motor for a 8532-07 Motor

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching