Is There a Trailer End 4-Round With Wires

Question

Question:

Do you have a 4-way round with a cable?

asked by: Steve M

0

Expert Reply:

Hi Steve,

There is not a trailer end 4-round that comes with the wiring attached, just the plug version, the Pollak Heavy-Duty, 4-Pole, Round Pin Trailer Wiring Connector - Metal - Trailer End # PK11402.

expert reply by: Kyle S

0

Answer 1

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 5

In order to match up the wheel studs for your Reliable 1206 hub, we'll need to know the full dimensions of the wheel stud you're replacing. In addition to the total length of the stud and its diameter and thread pitch, we'll also need to…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

According to Lippert, the mounting nuts should be torqued to 120 ft-lbs for the Axle Riser Kit - Single Square Torsion Axle - 3-1/2" Lift #LC382741.

view full answer...

Answer 8

The Buyers Products 45 Ton Pintle Hook #337PH45 does not have the 4 inch square bolt pattern but rather uses a different pattern. Vertically the holes are 3 inches on center. Horizontally the top row is 5-1/4 inches on center and the bottom is 6-1/2…

view full answer...

Answer 9

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 10

The Hayes Air Actuated Trailer Brake Controller - 1 to 4 Axles - Proportional #HA100400C mounts to the inside of your 2007 Nemar Essex at the dash just like other electric brake controllers will. It needs to be installed on the inside of the vehicle…

view full answer...

Answer 11

The adjustment holes on the Super Titan Forged Pintle Hook Plate part #RP38186 are 17/32" diameter so they will accept and are designed to be used with 1/2" bolts. It should not matter what brand pintle hook is used as the hole size and…

view full answer...

Answer 12

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Is There a Trailer End 4-Round With Wires

Product Page this Question was Asked From

Continue Researching