Idler Hubs, Bearings, Seals and Grease For a 2015 V22L ShoreLand'r Boat Trailer

Question

Question:

I am trying determine what size wheel bearings as well as wheel bearing hub assembly are needed for my ShoreLander boat trailer. Top is VIN # 1MDAHAR11FA573610 2015 V22L BLACK METALLIC Mig. Date: 047. 8064303 20-Nov-2014 3207818

asked by: Michael

0

Expert Reply:

Thank you for providing all the information. If you are going to replace your entire idler hub you would want the Stainless # KH84545S or Galvanized # DE36VR idlers hubs since its on a boat trailer. These will come with the Inner Race # L68111 and Outer Race # L44610 already in the hub. It will then use the Inner # L68149 and Outer # L44649 bearings along with the Seal Set # BB60002 to work with your Bearing Buddy Protectors # BB1980A-SS.

If you are going to reuse your hubs you would need to order the races along with the bearings.

We have the Seal Puller # PTW1219 and Install Kit # PTW83020 which will make removal and installation of the seals and races easier. We also have the Grease # LOC54FR that is recommend for your hubs with the Bearing Packer # PTW1218 to ensure you get grease fully pressed into the bearings before installing them

expert reply by: Bud M

0

Answer 1

Hey Jon, so the Bearing Buddy seal kit part #BB60002 that you referenced is the correct fit based on your bearing numbers.

view full answer...

Answer 2

While we do not carry a replacement cap which will allow you to convert your hubs from oil bath to grease we do have a hub and all the components you will need to install a new setup which can be filled with grease. You will need one of each per…

view full answer...

Answer 3

Appreciate the photo, and you look to have an equalizer that is 7-3/4 inches from center to center, and for an equalizer upgrade I recommend the E-Z Flex: - E-Z Flex Equalizers #K71-655-00 The E-Z Flex #K71-655-00 will do exactly what you are…

view full answer...

Answer 4

What you are experiencing is common on tandem axle trailers when little or no weight is on them. The weight compresses the suspension and would not allow this to happen, or at least not as easily. If you were to use the E-Z Flex Equalizers…

view full answer...

Answer 5

The only difference between the Demco Channel Tongue Trailer Coupler part #12564 and Demco Channel Tongue Trailer Coupler part #DM12717 is the bolt pattern which is just slightly different with one having an extra hole.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

Hey Kevin, for your Demco DA70 actuator you can use the Reverse Lockout Solenoid for Demco Hydraulic Brake Actuators #DM11993.

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Idler Hubs, Bearings, Seals and Grease For a 2015 V22L ShoreLand'r Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching