Lift Kit for a 2008 Keystone Everest

Question

Question:

What would I need to lift a 2008 Keystone Everest?

asked by: Rodney C

0

Expert Reply:

Hey Rodney, thanks for reaching out!

The Correct Track kits for Single # LC87120, Tandem # RR23QX, and Triple # RR55QX axle trailers are a solid choice to add up to 2" of lift to any standard axle setup. If that's what you have on your 2008 Keystone Everest then you'll be good to go, otherwise let me know what kind of axle and suspension system you have on your Keystone and I'll be more than happy to help you figure out the best lift kit for your trailer!

expert reply by: Jon G

0

Answer 1

The Demco Hijacker Autoslide #DM8550034 has a weight of 273 lbs. I've added a couple links to video reviews of this hitch for you to take a look at.

view full answer...

Answer 2

The Demco Hijacker Autoslide 5th Wheel Trailer Hitch part #DM8550034 weighs roughly 276 lbs. This is pretty much the only drawback of the Hijacker but it's worth it due to the huge added convenience factor. It can be used on a 2019 Ford F-350…

view full answer...

Answer 3

The important factors to consider is that your truck has an overall gooseneck/fifth wheel trailer towing capacity of 18,500 lbs and the max the trailer you are looking at could weigh is 16,900 lbs if loaded to it's capacity. So what that means is…

view full answer...

Answer 4

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 5

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 6

The Correct Track Trailer Alignment and Lift Kit #RR23QX will allow you to lift your 2021 Keystone Cougar 24RDS 1-1/4" or 2-1/4". This will bolt to your current leaf spring hangers and move the suspension mounting points further down giving…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 11

Beds shorter than 8 foot do commonly need a slider hitch David, but a lot of modern fifth wheel trailers are now made with tapered noses to help and in a lot of cases a slider isn't required. So if the trailer you plan to tow has a tapered nose…

view full answer...

Answer 12

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Lift Kit for a 2008 Keystone Everest

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching