Is The Demco Recon Gooseneck-to-5th Wheel Trailer Hitch # DM8550045 Safe To Use On Aluminum Beds?

Question

Question:

Is this ok to use on the newer super duty with the aluminum body I have gooseneck setup but would like to get this to use 5th wheel as well

asked by: Michael L

0

Expert Reply:

The Demco Recon Gooseneck-to-5th Wheel Trailer Hitch Adapter # DM8550045 is safe to use in the aluminum bed on your 2019 Ford F-250 Super Duty. You will need to your gooseneck ball does not sit over 5" above the bed otherwise you may need a shorter gooseneck ball.

expert reply by: Bud M

0

Mike

2/26/2024

Thanks it is under 5"

Reply

Answer 1

The Demco Recon Gooseneck-to-5th Wheel Trailer Hitch Adapter #DM8550045 referenced in your question uses a coupler at the base to securely attach to a standard 2-5/16 inch diameter gooseneck ball. Top and side coupler bolts hold it in place so that…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 6

The recommendation for the 10" diameter lube plate on a B&W Companion 5th Wheel Trailer has come from the manufacturer of the fifth wheel hitch, B&W. The Lube Plate for Reese 5th Wheel Trailer Hitches part #RP83002 will work just fine…

view full answer...

Answer 7

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 8

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 9

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...