Hardware Size and Torque Spec for Front TorkLift Tie-Down on a 2023 Ford Ranger

Question

Question:

Hey there, I am about to install the TorkLift camper tie down for the front of my ford ranger 5ft bed. What size are the bolts that I need to install? and what lbs/ft do I need for the wrench? Just want to make sure I have the tools ready. Thanks in advance!

asked by: Jake G

0

Expert Reply:

Thanks for reaching out, Jake!

The front TorkLift Tie-Downs # TL34YR for your 2023 Ford Ranger uses 1/2" bolts that need to be torqued to 75 ft-lbs according to my contact at TorkLift.

expert reply by: Jon G

0

Answer 1

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 2

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 3

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory…

view full answer...

Answer 4

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 5

Thanks for reaching out, Jake! The front TorkLift Tie-Downs #TL34YR for your 2023 Ford Ranger uses 1/2" bolts that need to be torqued to 75 ft-lbs according to my contact at TorkLift.

view full answer...

Answer 6

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 7

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 10

Yes you can absolutely use the HappiJac Qwik-Load Turnbuckles for Camper Tie-Downs #LC182895 with your TorkLift tie downs.

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

Great news Rick. The Firestone Ride-Rite Air Helper Springs #F2609 is compatible with the adaptive ride control on your 2024 GMC Sierra 1500 Denali. You can pair this with the Firestone Air Command #F56VV so you will be able to easily adjust the air…

view full answer...

Hardware Size and Torque Spec for Front TorkLift Tie-Down on a 2023 Ford Ranger

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching