Replacement Front Anchor Plates for HappiJac Tie-Downs On 2006 Dodge Ram 3500

Question

Question:

Hello. I have a 2006 dodge ram 3500 srw and I am looking for a happy jac plate replacement. I tries to search on your website but it seems that you only offer the complete kit. Do you happen to know if the plates are available as a separate item? Thank you.

asked by: Tyron B

0

Expert Reply:

We do have the replacement plates for your front HappiJac Camper Tie-Downs # LC182908-182928. What you need is the Replacement Front Anchor Plates for HappiJac Truck-Mounted Camper Tie-Downs # LC58AF

expert reply by: Robin H

0

Answer 1

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 2

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth…

view full answer...

Answer 3

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 4

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 8

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes you can absolutely use the HappiJac Qwik-Load Turnbuckles for Camper Tie-Downs #LC182895 with your TorkLift tie downs.

view full answer...

Answer 11

Your slide-in truck camper does not have electric brakes so the blue brake circuit wire from its 7-way connector is not used. All other lighting functions as well as 12V auxiliary power will be maintained on the other circuits. Please refer to the…

view full answer...

Answer 12

In regards to HappiJac Truck-Mounted Camper Tie-Downs like part #LC182908-182928, the front tie-down installs inside the bed on the front panel directly behind the cab. The rear tie-down then mounts to the bumper. They will not require removal of the…

view full answer...

Replacement Front Anchor Plates for HappiJac Tie-Downs On 2006 Dodge Ram 3500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching