Does Curt Rockerball Fit Curt Aluminum Ball Mount # C45296

Question

Question:

Does Item # c40047 fit Item # C45296? Thanks

asked by: Tracy G

0

Expert Reply:

Yes Tracy, the Curt Rockerball part # C40047 does fit the Curt aluminum ball mount part # C45293 that you referenced.

expert reply by: Jameson C

0

Answer 1

I attached an FAQ that details how to pick out the correct ball mount. Picking out the correct ball mount will allow your trailer to sit as level as possible. Basically you will first measure the height from the ground to the top of the receiver…

view full answer...

Answer 2

We have the perfect solution for you with the Curt RockerBall, part #C29FR for 2-5/16" ball or #C40047 for a 2" ball. It completely changes your towing experience by reducing jerking and jarring while towing. It absorbs the movement and…

view full answer...

Answer 3

The Curt Rockerball Shock Absorbing Hitch Ball has anti-Rotation Plate that is not compatible with all hitch mounts. This hitch ball is recommended to be mounted onto standard ball mounts not shock absorbing ones. I recommend the Curt RockerBall…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 7

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 10

The shortest gooseneck ball we have for the 2024 Chevy puck system is the Reese Elite Series Pop-In Ball #RP23FR. This is going to be very similar to the Curt ball you mentioned. I have included some dimensions of the Reese ball below. From the top…

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Does Curt Rockerball Fit Curt Aluminum Ball Mount # C45296

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching