Why Does The Correct Track Trailer Alignment and Lift Kit Have 2 Holes In Each Bracket?

Question

Question:

Looking this it has two bolts at the ??, my fifth wheel camper only has one hole at the 6 points ???????

asked by: Ronnie G

0

Expert Reply:

The Correct Track Trailer Alignment and Lift Kit # RR23QX has 2 mounting holes as you are able to select either a 1-1/4" rise or 2-1/4" rise depending on which hole you select to attach the brackets.

expert reply by: Bud M

0

Answer 1

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 2

Since you already have the Correct Track #RR23QX you should be able to adjust it and get your axles re-aligned. The kit allows you to make adjustments in 1/4" increments which will allow you to fix that 1/2" difference. I have attached the…

view full answer...

Answer 3

There are two different sized wet bolts used for the MORryde Suspension Upgrade Kits with 2.25" shackles. (1) of the wet bolts is 9/16" Diameter x 3-3/8" long and (1) of the wet bolts is 9/16" Diameter x 2-7/8" long. If you…

view full answer...

Answer 4

Thanks for all the pictures! It looks like your axles are already below your leaf springs so I recommend using the Correct Track Trailer Alignment and Lift Kit item #RR23QX you were looking at. This kit mounts to your spring hangers and moves the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 7

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 8

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 9

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 10

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 11

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Why Does The Correct Track Trailer Alignment and Lift Kit Have 2 Holes In Each Bracket?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching