Trailer Hitch Receiver and 4-Way Vehicle Wiring Harness Recommendation For a 2024 Toyota RAV4 Prime

Question

Question:

Will this hitch fit the 2024 Toyota RAV4 Prime?

asked by: Pam

0

Expert Reply:

Yes, the etrailer Trailer Hitch Receiver # e23ZR is confirmed to fit your 2024 Toyota RAV4 Prime. This will give you the more common 2" opening for carrying your hitch mounted receivers and ball mounts.

I recommend installing the Curt T-Connector Vehicle Wiring Harness # C56434 when you install the receiver. This will give you a 4-way flat connector which is the most common connector found on small trailers you would likely pull. It will also allow you to use Auxiliary Lights # C53201 with hitch mounted accessories which impair the view of your tail lights when loaded.

expert reply by: Bud M

0

Answer 1

The Curt Trailer Hitch Receiver #C87WR will fit all trim levels of the 2022 Mitsubishi Outlander. Since The Outlander Sport and Outlander PHEV are different models this receiver will not work on those vehicles. The Curt Trailer Hitch Receiver #C13398…

view full answer...

Answer 2

There is both a trailer hitch receiver and wiring harness that fits your 2024 Mitsubishi Outlander (so long as it is not the PHEV model). What you need is the following: - Curt Trailer Hitch Receiver #C87WR - Curt T-Connector Vehicle Wiring Harness…

view full answer...

Answer 3

It sounds like there is a short circuit that is overloading the running light circuit in the tow package wiring on your tow vehicle. The most likely culprit is a dirty or corroded trailer connector on the vehicle or trailer if not both. The first…

view full answer...

Answer 4

When properly installed a powered wiring harness such as #118460 will have power going to it all the time but not power coming out all the time because of the circuitry inside the converter box. The tail light wiring on a vehicle is only rated for so…

view full answer...

Answer 5

The issue with your running lights is indeed caused by the trailer and the lack of a solid ground. That said, this is an easy fix as all you will need to do is run a ground jumper wire from each running light to the main trailer connector ground and…

view full answer...

Answer 6

It sounds like there is a short somewhere along the wiring of your vehicle or trailer that is causing a fuse to blow every time you connect. The first thing I recommend doing is disconnecting the trailer and using a circuit tester like #PTW2993 to…

view full answer...

Answer 7

The most likely cause for the incorrect behavior of your trailer lights, where activating one turn signal causes all trailer lights to blink, is an insufficient ground (or a short to ground) on either the vehicle or the trailer. Since you re-wired…

view full answer...

Answer 8

Since the lights work on a different trailer then like you said the issue must be on the trailer. To determine the issue you will first want to check the trailers connector. If there is any dirt or corrosion you will need to clean it out on the pins…

view full answer...

Answer 9

The video you referenced shows the Tekonsha kit part #118505 install on a 2010 Toyota Prius like yours which is basically the exact same install as the Curt part #C56147 that you have. If there's a Hybrid Error warning light coming on I would…

view full answer...

Answer 10

According to Curt the wiring harness #C55567 does fit your hybrid model of the 2016 Toyota Camry. I've linked a video of the install on a 2012 Camry which is a similar process. The install details are also linked. If you need a trailer hitch as…

view full answer...

Answer 11

It is possible that during the installation of the fuses and relays that something got knocked loose or damaged. Check the fuse panels where those items were installed and see if anything is damaged or missing. Also, make sure the relays are in the…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...