Parts Needed For Adding 1,000LB Slipper Springs To a Cart With No Suspension

Question

Question:

Im interested in a 2-Leaf Slipper Spring w/ Radius End for 1,000-lb Trailer Axles - 24-5/8 Long Item # SP-177275. I need the a kit so I can add this to a cart that has no suspension.

asked by: Dave M

0

Expert Reply:

You will need 2 of the Front # CE14016G and Rear # CE14017G hanger brackets to attach 2 of the 2-Leaf Slipper Springs # SP-177275 to your cart. You will need 2 of the Zinc Shackle Bolts # TRFA73Z916DLNZ to attach the leaf springs to the front hanger. If you can tell what shape and size axle you have I can help you find the U-Bolt Kit you need. We have some like the 1-1/2" Square # CE23102 or 1-3/4" Round # CE23000 depending on the size of your axle.

expert reply by: Bud M

0

Answer 1

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 2

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 3

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 4

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 5

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 8

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...

Answer 9

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 10

When replacing shackle straps they should be the same length as the ones that were previously on your tandem axle trailer; replacing them with longer straps will result in additional play in your trailer suspension which could lead to additional wear…

view full answer...

Answer 11

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Answer 12

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Parts Needed For Adding 1,000LB Slipper Springs To a Cart With No Suspension

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching