How Far Does A Solera RV Awning Stick Out From The Wall When Closed

Question

Question:

What is the depth when closed? How far does it stick out from the wall when closed? Thank you!

asked by: Ben P

1

Helpful Expert Reply:

When closed the Solera XL 12V Power RV Awning # LCV000334919-362241 will stick out from the side of the trailer approximately 4-5".

expert reply by: Kevin C

1

Answer 1

When folded up into the stored position the TorkLift GlowStep Camper Scissor Steps #TLA7802 are approximately 9-1/2" deep. I confirmed with TorkLift that this specific model is designed to just fold up, lock in place and be ready to travel.

view full answer...

Answer 2

The 14-foot dimension shown for the Solera 12V XL Power RV Awning #LCV000334942-362241 refers to the outside to outside spacing of the two included 78-inch-tall wall-mount vertical brackets that contain the awning support arms. The fabric canopy…

view full answer...

Answer 3

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will…

view full answer...

Answer 4

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack…

view full answer...

Answer 5

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 6

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 7

M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while 1/2" threads are going to be 0.500" in diameter. We currently only have 1/2"-20 Lug Nuts…

view full answer...

Answer 8

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Answer 11

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement for…

view full answer...

Answer 12

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

How Far Does A Solera RV Awning Stick Out From The Wall When Closed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching