Are the Wheel Bolts, # RG02-020, 1/2"-20 Thread Size

Question

Question:

Is the thread size 20 on the bolt ?

asked by: Robert S

0

Expert Reply:

Yes, the Wheel Bolts, # RG02-020, are 1/2-20 bolts which seems to be the standard for many hubs, drums, and wheels. They also have the industry standard 60 degree cone and are fine threaded.

expert reply by: Michael H

0

Answer 1

Technically, a trailer rated for 10,000 lbs can have 5 lug hubs. They are most common on 3,500 lb axles but can be used on the rare 4,000 lb axles as well. You could have a gooseneck or 5th wheel trailer with the 10,000 lb capacity and tandem axle 5…

view full answer...

Answer 2

First things first; you can determine the specs on your current axle by checking for a sticker or plate attached to the axle itself (you'll usually find it close to the center of the axle). But with that being said, in the event that you…

view full answer...

Answer 3

In order to determine the correct bearings for your trailer, you will need to pull a hub and retrieve the inner and outer bearing numbers stamped into the metal of the bearings. We have 4 possible bearing kits for 3,500 pound axles. I have included a…

view full answer...

Answer 4

The teardrop style of fender is only available as a pair, so for your tandem axle trailer with 15 inch wheels, the teardrop style is the Tandem Axle Teardrop Trailer Fenders - Rounded Edges - Steel - 14" to 15" Wheels - Qty 2 #HP94VR. In…

view full answer...

Answer 5

The short answer is yes, you can replace your 3,500 lb axle with a 5,200 lb axle. The longer answer is that while you can change to a higher-rated axle, that does not mean your trailer has a higher weight capacity. The reason is, weight ratings are…

view full answer...

Answer 6

It sounds like potentially the Lionshead Trailer Wheel Lug Nut - 1/2"-20 - Stainless Steel - Qty 1 #LHLR103, which are a 1/2" x 20 thread lug with a 3/4" head that would match your vehicle's lugs. This is a 60 degree conical lug…

view full answer...

Answer 7

It would be odd for the 4-1/4 inch measurement to be accurate. I've attached an article on measuring bolt pattern for you to confirm your bolt pattern before ordering. If you do end up with the same measurements, you may want to consider changing…

view full answer...

Answer 8

I spoke with our resident tire expert and he confirmed that you will want to use Redline 1/2" x 1" wheel bolts with a 60 degree cone, part #RG02-020, for the Kenda 5.30-12 Bias Trailer Tire with 12" White Wheel #AM30780.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Are the Wheel Bolts, # RG02-020, 1/2"-20 Thread Size

Product Page this Question was Asked From

Continue Researching