Recommended Brake Controller Wiring Harness For 2013 Toyota Tundra

Question

Question:

Will this fit a 2013 Toyota Tundra Double Cab?

asked by: Marta

0

Expert Reply:

If your 2013 Toyota Tundra has the factory 7-way installed, the Curt Custom Wiring Adapter, part # C51362 will be what you need to connect the Curt Discovery Trailer Brake Controller, part # C84VV.

If you have a 4-way connector installed on your Tundra, part # C51515 is what you need. This harness is used on a vehicle that does not have a factory tow package or on one that has a brake control harness but is not equipped with a plug-in port. If your vehicle doesn't have a factory tow package, you'll have to hardwire the pigtail end of the adapter into your vehicle's wiring.

If you are planning on towing quite a lot and for a better towing experience, I recommend the Curt TriFlex Trailer Brake Controller, part # C24VV. This is a proportional brake controller that works with electric or electric over hydraulic brakes on your trailer. This controller will activate the brakes on your trailer in proportion to the braking action of your vehicle. Proportional brake controllers are easier on your brakes than the time-delayed controllers.

If you have the factory 7-way on your truck then the Curt Custom Wiring Adapter for Trailer Brake Controllers, part # C51362 is the adapter you need.

If you do not have a 4-way or 7-way connector at the rear of your Tundra, I recommend the Universal Installation Kit for Trailer Brake Controller, part # ETBC7.

expert reply by: Jeffrey L

0

Answer 1

Brake controllers are not vehicle specific. A wide variety of brake controllers will work for your 2013 Toyota Tundra. If you have a factory 7-way, then there are vehicle specific wiring harnesses to make installation easier. You can find those using…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 4

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...